1b. Internal Wire Compartment: Remove screw holding blower assembly (venturi) in place and lift assembly out of housing (Figure 6). Remove the wire compartment cover screw and place the cover in a secure place (Figure 7).
Plug 
Venturi 
Screws
Figure 6
NOTE: If the fan motor plug |
|
|
|
|
|
Screw |
|
| Wire | ||
|
| ||||
is connected to the fan |
|
| |||
housing receptacle, unplug |
|
|
| Compartment | |
so the blower assembly can |
|
|
|
| Cover |
be completely removed. |
|
|
|
|
|
|
|
|
|
| |
Figure 7
2.Run wiring from an approved wall switch carrying the appropriate rating. One neutral (white), one ground (green or bare copper), and three hot (black, red, yellow leads connected to the switch, one for each function). Secure the electrical wires to the housing with an approved electrical connector. Make sure you leave enough wiring in the box to make the connection to the fan’s receptacle.
NOTE: The fan’s receptacle wires might need to be pulled outside compartment for connection. Only pull the loose wires outside of compartment. Additional wires will be present.
4.Carefully tuck wires back inside wire compartment and replace wire compartment cover securing with the screw that was removed earlier.
SECTION 6
Completing the Installation
1.If the fan’s blower assembly was removed during the wiring process, reinstall the blower by reversing the directions in Step 1b in Section 5 Wiring.
2.Plug the fan’s quick connect motor cord into the receptacle. This cord will only fit one way into the receptacle (Figure 9).
Figure 9 |
3.Install the appropriate bulbs (not included) specific to your model (Figure 10):
3. From where you have chosen to access the fan’s junction | AK100L: 100 watt maximum, type A19 medium base | |||||||
incandescent bulb (not included) and a 7 watt maximum | ||||||||
box, connect the white wire from the house to the two white | ||||||||
type C7 (candelabra base) night light (not included). | ||||||||
wires from the fan. Connect one hot (black) wire from the wall | ||||||||
switch to the black wire from the fan (this is the fan control). | AK100FL: 26 watt maximum, 2 pin quad, fluorescent lamp | |||||||
Connect second hot (red) wire from the wall switch to the red | (not included) and a 7 watt maximum type C7 (candelabra | |||||||
wire from the fan (this is the night light control). Connect the | base) night light (not included). | |||||||
third hot (yellow) wire from the wall switch to the yellow wire |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
from the fan (this is the main light control). Connect the ground |
|
|
|
|
| |||
|
| Night Light | ||||||
wire from the house to the green wire from the fan (Figure 8). |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| ||
Use approved methods for all connections. |
|
|
|
|
|
|
| |
|
|
|
|
|
|
| ||
Supply from |
|
|
| |
house |
|
|
| |
White |
| Figure 10 | Lamp Holder | |
Hot | Hot |
| ||
(Black) | 4. Install the grill by squeezing the two ends of the springs | |||
(Red) | ||||
| ||||
Ground |
| together and installing them up into the slots on the fan’s | ||
|
| housing. Push the grill up into position (Figure 11). | ||
| Hot (Yellow) |
| ||
Figure 8 |
|
|
| |
210952012 Rev. B |
| www.airkinglimited.com | 3 of 12 | |