Operation

CAUTION

To reduce risk of ﬁre and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings, attics, crawl spaces or garages.

Always leave safety grilles and ﬁlters in place. Without these components, operating blowers could catch onto hair, ﬁngers and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation, maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

-To contact a qualiﬁed electrical installer.

-To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is recommended that a qualiﬁed electrician determine that the ground path is adequate.

Do not ground to a gas pipe.

Check with a qualiﬁed electrician if you are not sure the range hood is properly grounded.

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269 ** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

AK8800Ax - 710W, 5.95 Amps

A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase and install appropriate connector if necessary.

FEDERAL COMMUNICATION COMMISSION INTERFACE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

. Reorient or relocate the receiving antenna.

. Increase the separation between the equipment and receiver.

. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

. Consult the dealer or an experienced radio/TV technician for help

SUITABLE FOR USE IN DAMP LOCATIONS WHEN INSTALLED IN A GFCI PROTECTED BRANCH- CIRCUIT. INTENDED FOR OUTDOOR COVERED PATIO OR LANAI AREA.

Important Safety Notice

AK8800AS, AK8800AG specifications

The Zephyr AK8800AG and AK8800AS are cutting-edge microcontrollers designed for demanding applications in various industries. Their robust architecture and array of features make them suitable for tasks requiring high performance, efficiency, and reliability.

One of the primary features of the AK8800 series is its advanced ARM Cortex-M4 core, which provides a performance boost for processing complex algorithms while maintaining low power consumption. This makes the AK8800AG and AK8800AS ideal for battery-operated devices where energy efficiency is crucial. The 32-bit architecture supports high-speed processing, ensuring that real-time applications run smoothly without lags or interruptions.

Both models come equipped with an extensive memory system. They include up to 512KB of Flash memory and 128KB of SRAM, allowing for the storage of large programs and data sets. This substantial memory capacity enables developers to implement rich features in their applications without worrying about memory constraints. Additionally, the microcontrollers support external memory interfaces, facilitating the connection of additional storage options when more capacity is needed.

The AK8800 series is fortified with a wide range of integrated peripherals. These include a high-performance ADC (Analog-to-Digital Converter), SPI (Serial Peripheral Interface), I2C (Inter-Integrated Circuit), UART (Universal Asynchronous Receiver-Transmitter), and GPIO (General Purpose Input/Output) pins. These peripherals enhance connectivity and allow for seamless integration with various sensors, actuators, and other devices, making the AK8800AG and AK8800AS versatile solutions for IoT applications, industrial automation, and consumer electronics.

In terms of connectivity, the Zephyr AK8800 series supports multiple communication protocols, including wireless technologies. This aspect is essential for modern applications requiring remote communication, enabling developers to create connected solutions effortlessly.

Moreover, the AK8800AG and AK8800AS microcontrollers are built to withstand harsh operating environments. They feature rugged designs and are able to operate in a wide temperature range, making them suitable for industrial settings where reliability is paramount.

In conclusion, the Zephyr AK8800AG and AK8800AS microcontrollers represent an excellent choice for developers seeking powerful and flexible solutions for their embedded systems. With their advanced processing capabilities, ample memory, comprehensive peripheral support, and robust design, they are poised to meet the challenges of our increasingly connected world. Whether for IoT applications, industrial automation, or consumer electronics, these microcontrollers provide the performance and reliability needed for success.