Installation

GENERAL GUIDELINES

Before installing and /or using the cooker hood, please read these instructions carefully.

Before installing the cooker hood make sure the volt- age (V), frequency (Hz) indicated on the serial num- ber plate and specifications on the rating plate on the inside of the cooker hood correspond to the voltage and frequency of the mains supply.

The cooker hood must not be installed and connect- ed to flues where other appliances are installed and which run off other energy supplies other than elec- tricity (water heaters - boilers - cookers, range/gas etc). The extraction hood requires a 125mm extrac- tion pipe connected directly to the outside with an opening of a minimum cross section of 150cm2.

The hood must be installed with a distance of 650- 750mm between the cooker top/hob and the extrac- tion hood.The cooker hood must not be installed above cookers with eye-level grills.

ELECTRICAL CONNECTION

This cooker hood is designed for permanent fixture. Connect to mains supply. Check voltage and fre- quency given on the rating plate located on the inside of the hood. Connect the mains cable to a power socket or to a double pole switch with a con- tact gap of at least 3mm. The mains cable (type H05VV- F 2 x 0.75 mm2) is connected to terminals marked with the letters L (power line) and N (neutral) mounted on the hood and is secured in position by a cable gland. The mains cable must be connected to a suitable and easily accessible fixed power point. As the electrical installation must comply with the laws and regulations in force only a qualified and authorised electrician must install the hood including connecting it to a double pole switch with a contact gap of at least 3mm.

Connect the mains cable if provided with a plug to a power socket. The user must have access to the power socket to be able to connect and disconnect the plug once the hood is mounted and fixed or the mains cable can be plugged into a socket with a dou- ble pole switch with a contact gap of at least 3mm.

The manufacturer will not be responsible if the gov- erning health and safety laws are not observed which permit safe and correct use of the hood and electrical connections.

MAINTENANCE

Before servicing or repairing the hood make sure the appliance is disconnected from the mains supply either by removing the plug or switching the power socket to OFF.

CLEANING

Clean the outer part of the hood with a soft cloth and liquid detergent, do not use abrasive cleaning prod- ucts or scouring pads.

CHANGING THE LIGHT BULB

Before changing the light bulb, ensure that the appli- ance is not live (the switch should be in position 0 - OFF). Remove the metal anti-grease filters (Fig.5). Change the halogen light using a 230V halogen light, with an E14 coupling, max. 50W. Replace the metal anti-grease filters.

WARNINGS

“NOTE: the areas behind the filters are not intended to be cleaned”

Follow the cleaning instructions given by the manu- facturer and in particular take care that there are not grease deposits on the surface of the hood which could create a possible fire hazard. Make sure the electric hob rings or gas rings are always covered when in use to avoid heating the filter.

When frying never leave pans unattended as there is the risk of the oil overheating and catching fire. If reusing frying oil the fire risk is greater. Never pre- pare flame cooked food dishes under the hood. The air duct by the hood must not be conveyed into a flue used for other appliances that run off other energy supplies other than electricity. If the air is to be duct- ed, before installing make sure the flue is in good condition especially if it has been out of use for a long period of time. Always observe governing laws and regulations regarding ducting waste gases. All recommendations given must be scrupulously observed to avoid any possible fire hazard.

CONTROL PANEL

The control panel is situated on the front of the hood and comprises of a digital display and 6 touch con- trol switches with the following functions:

Fan ON/OFF Switch

Reduces the speed of the fan (Min speed 1)

Stainless Steel Box Hood specifications

Waterford Precision Cycles is renowned for its craftsmanship and attention to detail in the field of custom bicycles. Among their innovative offerings is the Stainless Steel Box Hood, a product designed with both functionality and aesthetics in mind. This high-performance component is particularly appealing to cycling enthusiasts who value durability without compromising style.

One of the standout features of the Waterford Stainless Steel Box Hood is its robustness. Constructed from premium-grade stainless steel, this component is engineered to withstand the rigors of daily riding and adverse weather conditions. Stainless steel is known for its resistance to corrosion, which ensures the longevity of the hood while maintaining its polished appearance. This makes it an ideal choice for cyclists who ride in various conditions, as the Box Hood won’t easily tarnish or rust over time.

Another significant aspect of the Box Hood is its engineered design, which enhances aerodynamics. The sleek, boxy shape reduces drag and provides a more streamlined experience for cyclists, making it especially beneficial for competitive riders looking to maximize speed. Additionally, the Box Hood is designed to fit seamlessly with a variety of bicycle frames, ensuring compatibility without compromising the aesthetic integrity of the overall bike design.

Waterford Precision Cycles has also integrated advanced technologies into the manufacturing process of the Box Hood. Utilizing precision machining techniques, each hood is crafted to exact specifications, ensuring a perfect fit and optimal performance. The combination of traditional craftsmanship and modern technology results in a component that not only looks exceptional but also functions at the highest level.

Another characteristic that sets the Box Hood apart is its versatility. It offers riders the opportunity to customize their bikes to align with personal preferences or style. Whether on a competitive track or a casual ride through the city, the Box Hood enhances the overall cycling experience.

In summary, the Waterford Precision Cycles Stainless Steel Box Hood combines durability, advanced aerodynamics, precision engineering, and customization potential. It's a thoughtfully designed component for discerning cyclists who appreciate both aesthetics and functionality, making it a worthy investment for any bike enthusiast looking to enhance their ride.