Mounting Holes | Universal Metal Industries ULT2830, ULT2824

PART 3 Determining Direction of Vent and Securing the Hood

MOUNTING HOLES:

Because the Trade-Wind®Ultra Series rangehood was designed for all applications, no mounting holes have been pre-drilled. This allows the hood (or liner) to be attached in the areas of the cabinet or wood hood canopy that have proper wood frame support. The hood should be attached to the wood framing through the top. Remove the filters. Mark and drill screw holes through the hood as required. Secure the hood by driving screws (provided by others) through the screw holes. NOTE: DRILLING THROUGH STAINLESS STEEL REQUIRES TITANIUM DRILL BITS.

BE CAREFUL NOT TO DRILL THROUGH THE UL LABEL OR INTO THE HOOD’S ELECTRICAL COMPONENTS.

DETERMINING THE DIRECTION OF VENTING (TOP, REAR AND RECIRCULATE):

TOP VENT

BACK VENT

RECIRCULATION

IMPORTANT NOTE: If hood is to be vented out the Top or Back, the charcoal filters must be removed.

Top Vent: Range hoods are shipped with the motor and blower installed to vent out the top. However, the vent covers in the rear vent opening and recirculation vent opening must be taped on all edges to prevent air leaks and vibration noise. The vent covers are not taped when shipped from the factory because the direction of venting may be changed. Vent covers can be placed on either the outside or inside of the hood. Vent covers placed on the inside of the hood should be neatly foil taped. Duct covers placed on the outside of the hood can be duct taped. If the rear vent and recirculation vent covers are not already in place, slightly bow the vent cover and place the side slots over both sides of the vent openings. Tightly fasten the motor & blower housing to the studs on the hood top. When installed correctly, the motor & blower housing will be approximately ½” from the back wall of the hood.

Back Vent: Unplug the electrical connection and remove the motor & blower housing from the hood.

IMPORTANT: Remove the vent cover from the rear vent opening. Slightly bow the vent cover removed from the rear vent opening and place the side slots over both sides of the top vent opening. The vent cover can be placed on the inside or outside of the hood. We recommend the inside. Vent covers placed on the inside of the hood should be neatly foil taped. Vent covers placed on the outside of the hood can be duct taped. Vent covers must be taped on all edges to prevent air leaks and vibration noise. Do not re-use the pieces of duct tape shipped with the hood. Reposition the blower housing to vent out the back of the hood and align the housing mounting brackets so that the housing tightly fits against the back wall. Securely fasten the motor & blower housing to the studs on the hood top. Reconnect the electrical connectors.

Recirculation: Note: “NRV” Models (No Recirculation Vent) do not have the recirculation feature.

Unplug the electrical connection and remove the motor & blower housing from the hood. IMPORTANT: Remove the vent cover from the front vent opening. Slightly bow the vent cover removed from the front vent opening and place the side slots over both sides of the top vent opening. The vent cover can be placed on the inside or outside of the hood. We recommend the inside. Vent covers placed on the inside of the hood should be neatly foil taped. Vent covers placed on the outside of the hood can be duct taped. Vent covers must be taped on all edges to prevent air leaks and vibration noise. Reposition the blower housing to vent out the front of the hood and align the housing mounting brackets so that the housing tightly fits against the front wall. Securely fasten the motor & blower housing to the studs on the hood top. Reconnect the electrical connectors.

Charcoal Filters: Charcoal Filters remove cooking odors. When properly installed in the hood, the charcoal material should be on the top side of the filter and not visible. Charcoal filters will not remove odors if washed and should be replaced periodically—every few months depending on usage. Replacement filters are available from

the manufacturer. Please call 800-875-3654.

CONNECTING TO THE VENT PIPE:

The hood is equipped with a metal damper. Attach the damper to the hood top or back side of the hood with at least two screws. Duct tape the edges to the hood. Be careful to not damage or tape over the damper blade. When connected to the back of the hood (horziontal ventilation), be sure the damper swings open from the bottom side; the hinge will be on the top. Otherwise, it will NOT close when the motor is off.

ULT2820, ULT2836, ULT2830, ULT2824 specifications

Universal Metal Industries has established itself as a leading provider of metal products, and its ULT2820, ULT2824, ULT2830, and ULT2836 series showcases the company’s commitment to quality, innovation, and performance. Each model in this series is meticulously engineered to meet a range of industrial applications while ensuring optimal functionality and versatility.

The ULT2820 is a compact solution designed for efficiency in tight spaces. With its robust construction, this unit is perfect for both light and moderate-duty tasks. It features advanced thermal protection, which prevents overheating during extended use, prolonging the lifespan of the equipment. The user-friendly interface allows quick adjustments, enabling faster productivity on the job.

Following the ULT2820, the ULT2824 model offers enhanced capacity and is ideal for businesses needing a more powerful solution. This unit is designed with high-strength components that enable it to handle heavier loads without sacrificing performance. Its energy-efficient motor reduces power consumption, making it a cost-effective choice for industrial environments.

Next in the lineup is the ULT2830, which provides an impressive balance between power and agility. This model incorporates cutting-edge technology, including smart sensors that monitor operational conditions in real-time. These sensors boost safety by automatically shutting down the unit in the event of anomalies, thus minimizing the risk of accidents. The ULT2830's compact design makes it easy to integrate into existing workflows.

Finally, the ULT2836 represents the pinnacle of performance in the series. Designed for heavy-duty applications, this model is equipped with advanced load-handling capabilities and impressive torque output. Its rugged frame can withstand challenging working environments, ensuring durability and reliability. Moreover, the ULT2836 boasts customizable features, allowing operators to configure the unit according to their specific requirements.

All models in the ULT series benefit from Universal Metal Industries' commitment to high-quality materials and state-of-the-art manufacturing processes. Each unit is designed for ease of maintenance, and serviceability is straightforward, reducing downtime significantly. With a focus on user experience, these models ensure that operators can achieve maximum productivity with minimal effort. Overall, the ULT2820, ULT2824, ULT2830, and ULT2836 exemplify Universal Metal Industries' dedication to delivering superior technology in metal work applications.