Texas Instruments TAS5110D6REF manual PSU Interface J150, = 6 Ω = 8 Ω

Page 16

PSU Interface (J150)

2.1 PSU Interface (J150)

The TAS5110D6DAD board must be powered from external power supplies. High-end audio performance requires a stabilized power supply with low ripple voltage and low output impedance.

Note:

The length of the power-supply cable must be minimized. Increasing the impedance of the PSU cable is equal to increasing the distortion for the amplifier at high output levels and low frequencies.

The maximum output stage supply voltage depends on the speaker load resistance. See the recommended maximum supply voltage in Chapter 4.

Description

RL = 4 Ω

RL = 6 Ω

RL = 8 Ω

Supply voltage for output stage

0 V – 20

V 0 V – 26.5 V

0 V – 26.5 V

 

 

Supply voltage for gate drive

22 V (min 16.5 V, max 26.5 V)

 

 

 

Supply voltage for control

5

V (min 4.5 V, max 5.3 V)

The recommended TAS5110 power-up sequence is shown in Figure 2–1. For proper TAS5110 operation, the RESET signal should be kept low during power up. RESET is pulled low during power up for 100 ms by the onboard low-drop linear regulator (U170).

Figure 2–1. Recommended TAS5110 Power-Up Sequence

Control Supply (3.3 V)

Gate-Drive Supply

Output Stage Supply

RESET

>1 ms

Figure 2–2. Pin Numbers at the PSU Interface (Top View)

4

3

2

1

Table 2–1. J150 Pin Description

Pin No.

Net Name at Schematic

Description

1

Power output stage

H-bridge supply voltage

 

 

 

2

GND

Ground

 

 

 

3

Gate-drive supply

Gate-drive supply voltage (I ≈ 90 mA)

 

 

 

4

5 V

Control supply voltage (I ≈ 100 mA)

2-2

Page 15 Page 17
Image 16
Page 15 Page 17
Contents User’s Guide Important Notice EVM Important Notice EVM Warnings and Restrictions Read This First Related Documentation From Texas Instruments Contents Figures Introduction TAS5110D6REF Features Tdaa System With TAS5026REF/TAS5036 and TAS5110D6REF ModulesPCB Key Map Physical Structure for the TAS5110D6REF Rough OutlineShort-Circuit Protection and Fault Reporting Circuitry Auto Recovery Loop Page System Interfaces PSU Interface J150 = 6 Ω = 8 ΩPSU Control Interface J160 This interface is not used in this boardPWM Interface J100 J100 Pin DescriptionPin No Net Name Description Page Electrical Specifications and Typical Characteristics Graphs TAS5110D6REF Electrical Specifications Physical SpecificationsTypical Characteristics Graphs THD+N vs Power Channel 1, 2, 3, 4, 5,FFT With -60 dB Input Signal Channel Channel Separation vs Frequency Channel 42m Schematic, Parts List, PCB Specification, and PCB Layout Input Section Front Speakers Rear Speakers Center Speaker & Subwoofer All rights belongs to Texas Instruments Incorporated 10R0 Ppm 100-mW metalfilm 100 nF 50 V 20% X7R 0805 Philips 2222 580 Kemet EEUFC1V102 MMBT2907A MY4S JST 4P-VH L263 TAS5110D6REF PCB Specification Page Page Page

TAS5110D6REF specifications

The Texas Instruments TAS5110D6REF is a high-performance audio amplifier that is designed to integrate seamlessly into various audio applications, including home theater systems, professional audio devices, and consumer electronic products. As a representative of Texas Instruments' commitment to innovation and quality, the TAS5110D6REF offers a robust set of features, technologies, and characteristics that elevate it to the forefront of the audio amplifier market.

One of the main features of the TAS5110D6REF is its advanced digital power management technology, which allows for high efficiency and low heat generation. This ensures that the audio amplifier can deliver powerful performance without compromising on energy efficiency or thermal stability. The amplifier supports a wide range of power supply voltages, making it adaptable to various use cases.

The TAS5110D6REF supports a variety of audio formats, including Class D amplification, which is known for its high fidelity and the ability to drive high current loads. This technology allows the power amplifier to produce audio output with minimal distortion while maintaining excellent sound quality. Furthermore, the Class D architecture enables the design of compact audio solutions.

Another notable characteristic of the TAS5110D6REF is its high output power capability, which allows it to drive large speakers with ease. The amplifier boasts an effective output of up to 200 watts per channel in stereo mode, providing an immersive listening experience even in larger environments.

In terms of compatibility, the TAS5110D6REF integrates easily with digital signal processing systems, enhancing sound quality through sophisticated algorithms for audio processing. It also features a variety of built-in protections, such as short-circuit and over-temperature protection, ensuring reliability and longevity in operation.

Additionally, the device offers advanced feedback loops, which contribute to maintaining sound integrity and minimizing signal loss during amplification. This feature is particularly important for ensuring that the original audio signal remains true to its source, making it an excellent choice for audiophiles and professional audio engineers alike.

Overall, the Texas Instruments TAS5110D6REF exemplifies cutting-edge audio amplification technology with its powerful output, energy-efficient operation, and high-performance characteristics. It is well-suited for a variety of applications, delivering high-quality sound reproduction that meets the demands of modern audio systems. With its combination of features and reliability, the TAS5110D6REF represents a significant advancement in the realm of audio amplification.
Top Page Image Contents