DIMENSIONS AND SPECIFICATIONS
INSTALLATION NOTES | MINIMUM SUPPLY PRESSURE REQUIRED |
| ELECTRICAL CHARACTERISTICS | |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Combustible Wall Clearances |
|
| Natural |
|
| Propane |
|
| Specifications | |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| 7" W..C.. (17..4mbar) |
| 11" W..C.. (27..4mbar) |
| 120 V, Single Phase, 60Hz, 1 amp | ||||||
Sides | Back |
|
| MANIFOLD PRESSURE REQUIRED, |
| |||||||||
|
|
| 6' (1829mm) | |||||||||||
|
|
|
|
| AFTER |
|
| |||||||
|
|
|
|
|
|
| power supply cord provided | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
6" (152mm) | 6" (152mm) | 3..5”W..C.. (8..75 mbar) |
| 10”W..C.. (25mbar) | ||||||||||
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
• IMPORTANT: Unit must be | • Gas Input Ratings shown are for |
| • NOTE: No cord and plug on export | |||||||||||
installed on legs for proper |
| installations up to 2,000 feet (610mm) |
| |||||||||||
|
| units.. Direct connection to junction | ||||||||||||
air circulation.. A minimum 4” |
| above sea level.. BTU input ratings must | ||||||||||||
| box.. | |||||||||||||
(101mm) air space must be |
| be derated for high altitude installations | ||||||||||||
|
|
|
| |||||||||||
maintained below unit for |
|
|
| VENTILATION |
|
| EXPORT VOLTAGES | |||||||
required air flow to burners.. |
|
|
|
|
|
|
|
|
|
|
|
| ||
• Commercial cooking equipment |
| • NOTE: Export voltages are available | ||||||||||||
|
|
|
| |||||||||||
ENTRY CLEARANCE |
| requires an adequate ventilation system.. | on request.. | |||||||||||
|
|
|
| Foradditional information, refer to the |
|
|
| |||||||
Crated | Uncrated |
| • | |||||||||||
| National Fire Protection Association’s |
| ||||||||||||
40" (1016mm) | 38" (965mm) |
|
| phase.. | ||||||||||
| Standard NFPA 96.. |
|
|
|
| |||||||||
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
| INPUT CHART - Natural Or Propane Gas |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
| Model |
| BTU/ | Kw |
| Gas |
| Shipping Weight |
| ||||
|
| Number |
| HOUR |
| Inlet |
| LBS.. |
| KGS.. |
| |||
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| 120,000 | 35..00 |
| 3/4" |
| 625 |
| 284 |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| 150,000 | 44..00 |
| 3/4" |
| 765 |
| 348 |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
| 180,000 | 52..70 |
| 1" |
| 905 |
| 411 |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
INSTALLATION
IMPORTANT: The installation must comply with local codes, or in the absence of local codes, with
CAN/CSA - B149 Installation Code – latest edition or with the National Fuel Gas Code NFPA 54 ANSI Z223..1 – latest edition.. All burner adjustments and settings shall be made by a qualified gas technician..
Serial Plate Location
All burner inputs are shown on the Serial/Rating Plate of each unit, located on the bottom of the control section near the front..
When corresponding with the factory or your local authorized factory service center regarding service problems or replacement parts, be sure to refer to the particular unit by the correct model number (including the prefix and suffix letters and numbers) and the warranty serial number.. The rating plate contains this information..
Page | Part # 4520498 (01/08) |