Faber PELLICANO manual Prepare the Cabinet, Install the Rangehood

Page 6

PREPARE THE CABINET

1.Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet and rear wall. Put a thick, protective covering over cooktops, set-in ranges or countertops to protect from damage or dirt.

2.Determine and clearly mark with a pencil the center line of the cabinet on the wall and on the underside of the cabinet where the rangehood will be installed.

3.Determine the proper cutouts for the ductwork. Make all necessary cuts in the walls or cabinets for the ductwork. Install the ductwork before mounting the rangehood.

4.If the cabinet bottom is recessed, wood filler strips need to be installed.

5.Drill four 3/16" clearance holes for hood mounting screws.

 

������

 

����������

 

������

����

�������

������

 

������������������

����������

������������������

�����

�������������

FIGURE 6

 

6. Cut a 6 1/2" diameter hole in cabinet bottom as shown.

����������

��������������������

����

��������

FIGURE 7

7.Determine and make the proper cutout for the Power Supply Cable. Use a 1 1/4" Drill Bit to make this hole. Run the Power Supply Cable through the wall or cabinet. DO NOT turn on the power until installation is complete. Use caulking to seal around the wire opening.

FIGURE 8

8.Remove the grease filters.

9.Remove the terminal box cover (located on the back wall of the hood. Remove the power supply cable knockout using a flat-blade screwdriver. Attach strain relief in power supply cable opening so that clamping screws are inside of rangehood.

10.Attach damper to exhaust opening on top of the range- hood using the two small screws from the hardware pack- age.

INSTALL THE RANGEHOOD

1.Place the rangehood mounting screws close to the holes in the cabinet bottom.

2.Lift rangehood into place while feeding wiring through strain relief.

3.Insert the screws through the clearance holes and start them into the rangehood.

4.Connect the vent system to the rangehood and seal all joints with duct tape.

5.Connect the Power Supply Cable to the rangehood. Attach the White lead of the power supply to the White lead of the rangehood with a twist-on type wire connector. Attach the Black lead of the power supply to the Black lead of the rangehood with a twist-on type wire connector. Connect the Green ( Green and Yellow ) ground wire under the Green grounding screw.

6.Replace the grease filters.

7.Turn the power supply on. Turn on blower and lights. If the rangehood does not operate, check that the circuit breaker is not tripped or the house fuse blown. If the unit still does not operate, disconnect the power supply and check that the wiring connections have been made properly.

Version 10/05 - Page 6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Lisez Bien Cette Fiche Avant Dinstaller LA Hotte PellicanoElectrical Requirements Venting RequirementsFor More Specific Ductwork INFORMATION, GO For residential use onlyAvertissement Pour Minimiser LES Risques Règlements DévacuationFiche Technique Électrique CORPORELS, Observer LES PrescriptionsParts Supplied for Installation Plan the Ductwork Recirculating InstallationsPersonal Injury Hazard Calculate the Ductrun LengthInstall the Rangehood Prepare the CabinetWarranty & Service Fuse Replacement if NeededUSE and Care Information Dimensions DU Produit Plan DU Conduit Installation Pour Recirculation DairRisque DE Blessure Calcul DE Longueur DU ConduitInstallation DE LA Hotte Préparation DE LarmoireGarantie ET Service Changement DES FusiblesUtilisation ET Entretien

PELLICANO specifications

The Faber PELLICANO is a remarkable writing instrument that has captured the admiration of pen enthusiasts and casual writers alike. Renowned for its unique blend of design, durability, and performance, the PELLICANO has solidified its position as a favorite among those seeking a reliable and stylish fountain pen.

One of the most notable features of the Faber PELLICANO is its ergonomic design. The pen is specifically crafted to provide comfort during extended writing sessions. Its triangular shape promotes a natural grip, reducing fatigue and ensuring a relaxed hand position. This is especially beneficial for students and professionals who rely on their writing instruments throughout the day.

The PELLICANO also incorporates advanced technology to enhance its functionality. The pen features a unique ink cartridge system that simplifies the refilling process. These cartridges are easy to replace and are available in a variety of vibrant colors, allowing users to express their individuality through their choice of ink. Additionally, the PELLICANO is compatible with standard converters, providing versatility for those who prefer bottled ink.

Durability is another hallmark of the Faber PELLICANO. Constructed from high-quality materials, this pen is designed to withstand the rigors of daily use. The robust plastic body is both lightweight and resilient, making it an ideal choice for students and professionals who demand reliability from their writing instruments. This durability is complemented by a polished stainless steel nib that delivers a smooth and consistent writing experience.

The design aesthetics of the PELLICANO are also worth noting. With a sleek and modern look, this pen is available in several attractive colors and finishes. Whether opting for a bright, eye-catching hue or a more understated classic look, users can find a PELLICANO that fits their personal style.

In conclusion, the Faber PELLICANO is a superb choice for anyone in search of a dependable fountain pen. Its ergonomic design, advanced ink cartridge technology, durable construction, and stylish aesthetics make it a standout writing instrument. Whether for everyday use or special occasions, the PELLICANO promises a pleasant writing experience that is sure to delight its users.
Top Page Image Contents