Faber Nova Prepare the Wall, Are Securely Fastened to the Wall, 90 cm 35 3/8 or

Page 5

PREPARE THE WALL

1.Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet and rear wall. Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt.

2.Determine and clearly mark with a pencil the center line on the wall where the rangehood will be installed.

3.TheNovaattachestothewallbythreemountingbrackets, points 1, 2 and 3 in FIGURE 5. The canopy of the rangehood hangs from two metal flanges that extend from bracket #1. This bracket must be mounted with the flanges on the bottom of the bracket. The dimensions in FIGURE 5 are for mounting the canopy 24" above the cooking surface.

If a backsplash is to be used with this rangehood, it must be installed before the rangehood. Installation instructions for the backsplash are supplied in its box. The height of the backsplash will determine the bottom edge of the canopy.

FIGURE 5

4.The chimney attaches to the wall by two additional brackets, points 2 and 3 in FIGURE 5 which illustrates the positioning of the chimney brackets. The largest bracket, #2, should be installed about 1/8" away from the ceiling. The middle bracket ( bright metal ) must be installed with the ends touching the wall and the curves facing outward. The middle bracket must be installed at the bottom point of the upper chimney sleeve.

Determine the proper location for each bracket and install the brackets on the wall. MAKE SURE THAT THE BRACKETS

ARE SECURELY FASTENED TO THE WALL.

5.Determine and make all necessary cuts in the wall for the ductwork. Install the ductwork before the rangehood.

6.DeterminetheproperlocationforthePowerSupplyCable as indicated in FIGURE 6. Use a 1 1/4" Drill Bit to make this hole. Run the Power Supply Cable. Use caulking to seal around the hole. DO NOT turn on the power until installation is complete. For remote blowers, a separate wiring cable is required. DO NOT WIRE THE REMOTE BLOWER INTO THE FIELD WIRING HOUSING OR CONNECT WITH THE POWER SUPPLY CABLE.

90 cm 35 3/8" or 30"

FIGURE 6

INSTALL THE RANGEHOOD

1.Remove the unit from the carton and place on a flat surface for assembly. Cover the surface to prevent accidental damage. Remove all parts including the mounting hardware before discarding the carton.

2.Remove the grease filters from the unit and set aside. The grease filters are removed by pressing the handle in front of the filter as indicated in FIGURE 7. When replacing, make sure that the filters are properly positioned with the handles in front and visible.

FIGURE 7

Version 11/00 - Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Nova Lisez Bien Cette Fiche Avant Dinstaller LA HotteElectrical Requirements Venting RequirementsFiche Technique Électrique Règlements DévacuationInstallation Dimensions Tools Needed for InstallationParts Supplied for Installation Parts Needed for InstallationPrepare the Wall Install the RangehoodAre Securely Fastened to the Wall 90 cm 35 3/8 orFor ductless installations USE and Care Information Warranty & ServiceCalcul DE Longueur DU Conduit Assemblage DE LA HottePréparation DU MUR Sont Bien Installées AU MURInstallation DE LA Hotte Pour les installations sans conduit Utilisation ET Entretien Garantie ET Service4324289

Nova specifications

Faber Nova is an innovative range hood designed to revolutionize the kitchen ventilation experience. Known for its blend of cutting-edge technology and sophisticated design, Faber Nova not only elevates the aesthetic of any kitchen but also ensures exceptional air quality and comfort during cooking.

One of the main features of the Faber Nova is its powerful suction capability. With a high-performance motor, it efficiently removes smoke, odors, and grease from the air, maintaining a fresh environment while you cook. The hood offers various suction levels, allowing users to customize performance based on the intensity of cooking. Whether you're simmering a delicate sauce or searing meat at high temperatures, Faber Nova adapts to your needs.

Another standout characteristic of the Faber Nova is its whisper-quiet operation. It incorporates advanced noise-reduction technologies that ensure minimal sound disturbance, even on higher settings. This feature is particularly advantageous for open-concept kitchens where maintaining a peaceful atmosphere is essential.

The Faber Nova also embraces smart technology with its integrated touch controls and remote operation capabilities. Users can easily adjust settings, including light levels and fan speeds, with just a tap or remotely via a smartphone app. This modern touch makes it simple to manage kitchen environments efficiently.

In terms of design, Faber Nova epitomizes elegance. It is available in various finishes, including stainless steel, matte black, and glass, allowing it to seamlessly integrate into diverse kitchen styles. Its sleek and minimalist appearance enhances the overall ambiance of the space.

In addition, the Faber Nova features energy-efficient LED lighting that illuminates the cooking area effectively while consuming minimal power. The lights are designed to provide clear visibility without adding excess heat, ensuring a comfortable cooking experience.

Maintenance is simplified with the Faber Nova, as it includes grease filters that are easy to remove and wash. This feature promotes hygiene and ensures that the appliance remains in optimal working condition over time.

In conclusion, Faber Nova is a versatile and high-performing kitchen hood that combines powerful ventilation, smart technology, elegant design, and user-friendly features. For anyone looking to enhance their kitchen ventilation experience, the Faber Nova stands out as a top choice, promising reliability and sophistication.
Top Page Image Contents