Faber Agio installation instructions Prepare the Cabinet, Install the Rangehood

Page 5

30" or 36" or 23 5/8" (60 cm)

FIGURE 7

PREPARE THE CABINET

1.Disconnect and move freestanding range from cabinet opening to provide easier access to upper cabinet and rear wall. Put a thick, protective covering over cooktop, set-in range or countertop to protect from damage or dirt.

2.Determine and clearly mark with a pencil the center line of the cabinet on the wall and on the underside of the cabinet where the rangehood will be installed.

3.The Agio attaches to the cabinet by four black screws. Mark the cabinet and insert the screws into the underside of the cabinet as shown in FIGURE 8. Do not tighten the screws.

30" or 36" or 23 5/8" (60 cm)

FIGURE 8

4.Determine the proper cutouts for the ductwork. Make all necessary cuts in the walls or cabinets for the ductwork. Install the ductwork before mounting the rangehood.

5.Determine the proper location for the Power Supply Cable. Both possible locations are given in FIGURE 9. Use a 1 1/4" Drill Bit to make this hole. Run the Power Supply Cable. Use caulking to seal around the hole. DO NOT turn on the power until installation is complete.

30" or 36" or 23 5/8" (60 cm)

FIGURE 9

INSTALL THE RANGEHOOD

1.Remove the unit from the carton and place on a flat surface for assembly. Make sure to cover the surface to prevent accidental damage. Remove all parts including the Backdraft Damper, Screws, and Literature Package before discarding the carton.

2.Remove both grease filters from the unit and set aside. The rangehood is shipped from the factory with the backdraft damper attached inside. Using a Phillips head screwdriver, remove the backdraft damper by loosening the screw marked with a red dot on top of the rangehood.

3.Before installing, the rangehood must be adjusted for venting. For ductless installations, read the following section which discusses special requirements for these installations before continuing.

For Horizontal or Vertical ducting, the respective exhaust knockout must be removed. Each knockout is attached to the rangehood by four points. Using a flat blade screwdriver or utility knife, remove the exhaust knockout. Save this plate as it must be used to block the ductless exhaust grill. FIGURE 10 shows the location of the knockouts for both horizontal and vertical. ONLY ONE must be removed.

Version 10/05 - Page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Agio Lisez Bien Cette Fiche Avant Dinstaller LA HotteElectrical Requirements For More Specific Ductwork INFORMATION, GOFor residential use only Ducted fans must always be vented to the outdoorsFiche Technique Électrique Règlements DévacuationAvertissement Pour Minimiser LES Risques CORPORELS, Observer LES PrescriptionsPlan the Ductwork Plan the DuctworkPrepare the Cabinet Install the RangehoodIf the Rangehood does not Operate Ductless InstallationsCustomizing Your Rangehood Warranty & ServiceSide View of the Rangehood USE and Care InformationPréparation DE LʼARMOIRE PlanificationInstallation DE LA Hotte SI LA Hotte NE Fonctionne PAS Installations Sans ConduitUtilisation ET Entretien Personnaliser LA Hotte4324281

Agio specifications

Faber Agio is an innovative and stylish kitchen appliance that redefines the modern cooking experience. Known for its cutting-edge design and functionality, Faber Agio represents a blend of artistry and technology, making it a popular choice for both professional chefs and home cooks alike.

One of the standout features of Faber Agio is its powerful suction capability. Equipped with advanced extraction systems, it effortlessly eliminates unwanted odors, smoke, and steam generated during cooking. This ensures a fresher and cleaner kitchen environment, enhancing the overall cooking experience. The high-performance motors are designed to provide efficient airflow, making them highly effective even in larger kitchens.

The Faber Agio also boasts eco-friendly energy consumption. With its commitment to sustainability, this product is engineered to reduce environmental impact while still delivering top-notch performance. Energy-efficient settings allow users to minimize energy consumption without sacrificing suction power, making it an excellent choice for those conscious of their ecological footprint.

Another notable characteristic of the Faber Agio is its sleek and modern aesthetic. The appliance features a minimalist design with high-quality materials that seamlessly blend into any kitchen decor. The use of glass and stainless steel not only creates an elegant appearance but also ensures durability and ease of cleaning. The intuitive interface with touch controls adds to the modernity, allowing users to operate the appliance effortlessly.

Technologically, Faber Agio is equipped with various smart features that enhance usability. The integrated LED lighting illuminates the cooking surface, providing better visibility while preparing meals. Additionally, the appliance comes with adjustable speed settings, enabling users to customize the airflow according to their cooking needs. Some models even offer remote control functionality, allowing for convenient operation from a distance.

Safety is also a priority in the design of the Faber Agio. Features such as thermal overload protection ensure that the appliance operates safely under high-performance conditions. This dedication to safety paired with intuitive design makes it an ideal choice for families and culinary enthusiasts alike.

In conclusion, Faber Agio combines innovation, practicality, and elegance, making it a standout choice in the realm of kitchen appliances. With its powerful suction, energy efficiency, modern design, and smart technology features, it enhances the cooking experience while taking into account the importance of sustainability and safety.
Top Page Image Contents