Zanussi ZDT 5044 manual Starting a washing programme, Unloading the dishwasher

Page 14

Starting a washing programme

In this fully integrated appliance the controls are located on the top of the door. When selecting a programme, the door needs to be open.

1.Check that the baskets have been loaded correctly and that the spray arms can rotate freely

2.Turn on the water tap

3.Press the On/Off push button

All the indicator lights of the programme selection push buttons illuminate (setting mode).

7. Unloading the dishwasher

Hot dishes are sensitive to knocks. The dishes should therefore be allowed to cool down before removing from the appliance.

Empty the lower basket first and then the upper one; this will avoid water dripping from the upper basket onto the dishes in the lower one.

Water may appear on the sides and the door of the dishwasher as the stainless steel will eventually become cooler than the dishes.

When the washing programme has finished, it is recommended that the dishwasher is unplugged and the water tap turned off.

4. Setting and starting the programme

To select a programme, press the programme push button of the washing programme you wish to select (see "Washing programmes" chart).

The corresponding indicator light remains illuminated while the other programme push buttons indicator lights turn off. The start of the programme will occur only after the closure of the door, until this moment you can modify the selection made.

Close the dishwasher door, the programme will start automatically.

5. To interrupt or cancel a washing programme in progress

Interrupt or cancel a washing programme in progress ONLY if it’s absolutely necessary

Attention! Hot steam may escape when the door is opened. Open the door carefully.

Interrupt a washing programme in progress

Open the dishwasher door; the programme will stop. Close the door; the programme will start from the point in which it was interrupted.

Cancel a washing programme in progress

Open the dishwasher door.

Press simultaneously the function push buttons 2 and 3 for about 2 seconds, the indicator light of the push button corresponding to the running programme starts flashing for about 2 seconds.

After about 2 seconds the indicator lights of all the programme push buttons will illuminate indicating that the running programme has been cancelled and that the machine has returned to setting mode.

(If a new washing programme will be selected, check that there is detergent in the detergent dispenser).

6. End of the washing programme

The dishwasher will automatically stop and an audible signal informs you of the end of the washing programme. Hot steam may escape from the appliance when opening the door immediately after the end of the programme, therefore, open the door carefully.

The end of programme indicator light is illuminated. The indicator light of the programme just ended remains on.

Switch off the dishwasher by pressing the On/Off push button.

14

Image 14
Contents Dishwasher Contents Child safety Safety instructionsInstallation DisposalDescription of the appliance Control panelFactory setting audible signals activated Audible signalsDeactivation/activation of the audible signals Water softener Prior to using for the first timeAudible signals ExampleFilling with salt To fillRinse aid Adjusting the doseFactory setting inflow of rinse aid activated Filling with rinse aidLower basket Daily useLoading cutlery and dishes Are of limited suitabilityUpper basket Adjusting the height of the upper basketCutlery basket To move to the higher position proceed as followsUse of detergent Fill with detergentConcentrated detergent Different kinds of detergentDetergent tablets Combi detergentsWashing programmes Starting a washing programme Setting and starting the programmeTo interrupt or cancel a washing programme in progress Unloading the dishwasherFrost precautions Maintenance and cleaningCleaning the filters Prolonged periods of non-operationFault code / malfunction Possible cause Solutions Flashing fault code appearsThere are problems when operating the dishwasher Fault Possible cause SolutionsDishes are wet and dull Dishes are not cleanWash results are not satisfactory Water drops have dried onto glasses and dishesService and Spare Parts Customer Care DepartmentEuropean Guarantee Guarantee ConditionsStandard guarantee conditions ExclusionsLevelling Installation instructionsBuilding-in Fixing to the adjacent unitsGreen and Yellow Earth Blue- Neutral Brown- Live Water outlet hose connectionElectrical connection Proceed as followsHints for test centres Cup racks position aPage From the Electrolux Group. The world’s No.1 choice