Protecting the Amplifier, Automatic Internal Fuse

SS6 and SS4 Speaker Selector

Installation Instructions

Adding Speaker Volume Controls

We recommend that you connect all your speakers to in-wall volume controls (like the Sonance VC60S/R) and then to the speaker selector (see ‘Rooms 2 – 6’ in Figure 2, on page 3). This gives you independent volume balancing and control in all speaker locations: Your receiver's volume control acts as the Master Volume, and each individual pair of speakers can be either OFF, or ON at its own volume level, independent of the other speakers connected in the system.

Protecting the Amplifier

The speaker selector includes a Protection switch located underneath the selector, on the right side. To protect your receiver or amplifier Sonance strongly recommends that you leave the Protection switch engaged at all times. Always operate your receiver or amplifier within its rated power range and within the power range of the speaker selector.

•To ENGAGE the Protection circuit, slide the red switch towards the back of the selector.

•To DISENGAGE the Protection circuit, slide the red switch towards the front of the selector.

Important: Turning the protection switch OFF allows greater power to your speakers, but may damage your receiver/amplifier.

Automatic Internal Fuse

The SS6 and SS4 have an internal fuse that will disconnect all of the speakers if the current draw through the unit exceeds a safe level. After the current draw returns to a safe level the fuse will automatically reset and re-connect all of the speakers.

Important: If the speaker selector continually turns the speakers OFF and ON, one or more of the following unsafe conditions exists in the audio system:

•The amplifier’s volume is set too high.

•The amplifier’s power output exceeds the Maximum Amplifier Power ratings as described in the Specifications section below.

•There is a short-circuit in one or more of the speaker wires.

To ensure safety, correct any and all of these conditions before operating the audio system again.

Specifications:

Power Handling:

Maximum Amplifier Power with Protection circuit ENGAGED and ALL pairs of speakers operating: 40 watts RMS per channel

Max i mum Amplifier Power with Protection circuit NOT engaged and ONE (1) pair of speakers operating: 120 watts RMS per channel

Protection Circuitry:	Resistive in-line
Switch Type:	Slide-slide, self-cleaning
Frequency Response:	20Hz – 20kHz
Dimensions (W x H x D):	SS6 — 11¼” x 2” x 7” (286mm x 51mm x 178mm)
	SS4 — 8½” x 2” x 7” (216mm x 51mm x 178mm)

SS6 specifications

The Sonance SS6 represents a remarkable fusion of cutting-edge technology and elegant design, catering to the needs of audiophiles and casual listeners alike. Engineered primarily for in-ceiling or in-wall installation, the SS6 speaker system is built to provide high-quality audio performance that blends seamlessly into any environment.

One of the standout features of the Sonance SS6 is its advanced speaker architecture. It incorporates a 6.5-inch polypropylene cone woofer designed to deliver rich and balanced sound across a wide frequency range. This woofer is specifically crafted to reproduce deep bass notes while maintaining clarity in mids and highs. Complementing the woofer is a 1-inch pivoting aluminum dome tweeter that ensures accurate high-frequency response. This pivoting capability allows users to direct sound towards specific listening areas, enhancing the overall audio experience.

The SS6 also utilizes Sonance's proprietary technologies, including the Patented “Vented” design, which helps to minimize distortion and improve overall sound quality. This design feature ensures that the speakers perform exceptionally well, providing clear sound even at higher volumes. In addition, the speakers are equipped with moisture-resistant materials, making them suitable for installation in environments prone to humidity, such as bathrooms and patios.

Aesthetically, the Sonance SS6 excels with its low-profile design. The speaker grille can be painted to match the ceiling or wall, allowing for a custom look that blends in with any décor. This is particularly beneficial in home theaters and living spaces where visual appeal is just as important as audio performance.

Installation is made easier with the SS6’s built-in dog legs and easy-to-use mounting brackets, which provide a secure fit in a variety of wall and ceiling depths. This allows both professional installers and DIY enthusiasts to achieve optimal placement with minimal effort.

In terms of versatility, the Sonance SS6 is compatible with a variety of audio systems and can be used in stereo or surround sound setups. Its ability to work seamlessly with both home theater systems and multi-room audio setups enhances its appeal for users who appreciate a comprehensive audio experience.

In summary, the Sonance SS6 combines innovative technology, aesthetic integration, and versatile performance in a compact design, making it a premier choice for anyone seeking superior in-ceiling or in-wall audio solutions. Whether for a cinematic experience or subtle background music, the SS6 is engineered to meet diverse audio demands while effortlessly enhancing the ambiance of any space.