Frigidaire 318205412 Important Notes to the Installer, Important Note to the Consumer

Page 3

induction COOKTOP INSTALLATION INSTRUCTIONS

Important Notes to the Installer

1.Read all instructions contained in these installation instructions before installing the cooktop.

2.Remove all packing material before connecting the electrical supply to the cooktop.

3.Observe all governing codes and ordinances.

4.Be sure to leave these instructions with the consumer.

5.Only certain cooktop models may be installed over certain built-in electric oven models. Approved cooktops and built-in ovens are listed by the MFG ID number and product code.

Important Note to the Consumer

Keep these instructions with your Use and Care Guide for future reference.

IMPORTANT SAFETY INSTRUCTIONS

•Be sure your cooktop is installed and grounded properly by a qualified installer or service technician.

•This cooktop must be electrically grounded in accordance with local codes or, in their absence, with the National Electrical Code ANSI/NFPA No. 70—latest edition in the United States.

WARninG The electrical power to the cooktop must be shut off while line connections are being made. Failure to do so could result in serious injury or death.

Provide Electrical Connection

Install the junction box under the cabinet and run 120/240 or 120/208 Volt, AC wire from the main circuit panel. NOTE: DO NOT connect the wire to the circuit panel at this time.

Electrical Requirements

Observe all governing codes and local ordinances.

1.A 3-wire or 4-wire single phase 120/240 or 120/208 Volt, 60 Hz AC only electrical supply is required on a separate circuit fused on both sides of the line (time-delay fuse or circuit breaker is recommended). DO NOT fuse neutral.

2.A circuit breaker or fuse rated at 40 Amp is recommended for the 30" model and a circuit breaker or fuse at 50 Amp is recommended for the 36" model.

NOTE: Wire sizes and connections must conform with the fuse size and rating of the appliance in accordance with the National Electrical Code ANSI/NFPA No.

70–latest edition and local codes and ordinances.

WARninG An extension cord must not be used with this appliance. Such use may result in a fire, electrical shock, or other personal injury.

3.The appliance should be connected to the fused disconnect (or circuit breaker) box through flexible armored or nonmetallic sheathed cable.

The flexible armored cable extending from this appliance should be connected directly to the grounded junction box. The junction box should be located as shown in Figure 2 with as much slack as possible remaining in the cable between the box and the appliance, so it can be moved if servicing is ever necessary.

4.A suitable strain relief must be provided to attach the flexible armored cable to the junction box.

Unpacking Instructions

1.Unpack and visually inspect the cooktop.

2.Be sure the bottle of cleaner conditioner packed in the literature bag is left where the user can find it easily. It is important that the ceramic-glass cooktop be pretreated before use. See Cooktop Cleaning and Maintenance section in the Use and Care Guide.

Electrical Connection

Connect the flexible armored cable that extends from the surface unit to the junction box using a suitable strain relief at the point the armored cable enters the junction box. Then make the electrical connection as follows.

Electrical ground is required on this appliance.

This appliance is equipped with a copper conductor flexible cable. If connection is made to aluminum house wiring, use only special connectors which are approved for joining copper and aluminum wires in accordance with the National Electrical Code and local codes and ordinances. Improper connection of aluminum house wiring to copper leads can result in a short circuit or fire. Follow the connector manufacturer recommended procedure closely.

This appliance is manufactured with a supply wire and a frame connected green or bare copper grounding wire.

DO NOT ground to a gas supply pipe. DO NOT connect to electrical power supply until appliance is permanently grounded. Connect the ground wire before turning on the power.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Induction Cooktop Installation Instructions On front page except for J and K Model and Serial Number LocationElectrical Requirements Important Notes to the InstallerImportant Note to the Consumer Provide Electrical ConnectionWire Grounded Junction BOX Wire Grounded Junction BOX Cooktop Installation Before You Call for ServiceChecking Operation With AN Electric Cooktop Mounted Above Cutout Dimensions Width Depth HeightInduction Cooktop Insotesallation Instructions Instrucciones DE Instalación Para LA Cubierta DE Inducción Figura 2 EL Corte DE LA Parte Superior DEL Armario Ubicación del número de modelo y de serieRequisitos eléctricos Notas importantes para el instaladorNota importante al consumidor Provea conexión eléctricaDE 3 Alambres Puesta a Tierra DE 3 Alambres Puesta a Tierra Si el cable de la unidad es equipada con 4 alambresInstalación de la estufa Revisión de operaciónAntes de llamar al servicio CON Tapa DE Cocina Montada Dimensiones DE Abertura Anchura Profundidad AlturaPage 30 Min. * 76.2 cm Instructions Dinstallation ImportantesMin Dégagement minimal de ModèleDirectives Importantes DE Sécurité Câble dalimentation Fil Blanc neutre Fils RougesFils noirs Boîte DE Jonction À 4 Fils Boîte DE Jonction À 3 Fils Mise À LA TerreInstallation de la table de cuisson 208/240 Volt, boîte de jonction pour le four encastré Dimensions DE Louverture Largeur Profondeur Hauteur

318205412 specifications

The Frigidaire 318205412 is a high-quality replacement oven igniter that is widely recognized for its reliability and efficiency in gas appliances. Designed to fit various Frigidaire and other compatible gas ranges, this igniter plays a crucial role in igniting the gas and ensuring your culinary creations are cooked to perfection.

One of the standout features of the Frigidaire 318205412 is its durable construction. Made from high-quality materials, the igniter is designed to withstand the high temperatures of an oven environment, providing long-lasting performance. Its robust design helps prevent premature failure, making it a cost-effective choice for homeowners.

The installation of the 318205412 igniter is user-friendly, making it accessible for DIY enthusiasts who prefer to handle repairs without professional help. The igniter typically comes with detailed instructions, allowing users to easily replace their old igniter and quickly get back to cooking. Its compatibility with various models means that many consumers can benefit from this single product, streamlining the repair process.

In terms of technology, the Frigidaire 318205412 uses a hot surface ignition method. This technology is known for its efficiency, as it requires minimal energy to generate sufficient heat to ignite gas. Unlike traditional igniters that rely on flames, this hot surface igniter produces a steady glow that ignites the gas quickly and safely, reducing the risk of gas buildup.

Another characteristic of the Frigidaire 318205412 igniter is its heat distribution capabilities. Once activated, the igniter evenly distributes heat throughout the oven, helping to ensure that food cooks uniformly. This feature is particularly appreciated by home cooks and professional chefs alike, as it leads to better baking results and more consistent meal preparation.

In conclusion, the Frigidaire 318205412 replacement oven igniter is a reliable, efficient, and easy-to-install component designed to enhance the performance of Gast ovens. With its durable construction, advanced hot surface ignition technology, and excellent heat distribution, it is an essential part for anyone looking to maintain their gas range in optimal condition. By investing in the Frigidaire 318205412, consumers can enjoy more reliable cooking experiences and increased longevity for their appliances.
Top Page Image Contents