Frigidaire 318203873 manual Before you call

Page 20

 

 

Before you call

 

Solutions to Common Problems

 

 

 

 

OCCURRENCE

 

POSSIBLE CAUSE/SOLUTION

Range is not level.

 

Poor installation. Place oven rack in center of oven. Place a level on the oven rack.

 

 

Adjust leveling legs at base of range until the rack is level. When range is level,

 

 

cooktop may appear out of alignment if countertop is not level.

 

 

 

 

 

 

Weak, unstable floor. Be sure floor is level and can adequately support range. If floor

 

 

is sagging or slopping, contact a carpenter to correct the situation.

 

 

 

 

 

 

Kitchen cabinet misalignment may make range appear to be unlevel. Be sure

 

 

cabinets are square and have sufficient room for range clearance.

 

 

 

 

Cannot move appliance easily. Appliance must be accessible for service.

Cabinets not square or are built in too tight. Contact a cabinet maker to correct the problem.

Contact builder or installer to make appliance accessible.

Carpet interferes with range. Provide sufficient space so range can be lifted over carpet.

Gas line is hard-plumbed. Have a flexible C.S.A international approved metal appliance connector installed.

Entire range or oven does not operate.

Make sure cord/plug is plugged tightly into outlet.

Service wiring is not complete. Call an authorized servicer.

Electrical power outage. Check house lights to be sure. Call your local electric company for service. Surface burners can be lit manually.

*Oven control beeps and displays any F code error (for example F11)

Electronic control has detected a fault condition. Press STOP/CLEAR to clear the display and stop beeping. Reprogram oven. If fault recurs, record fault number. Press STOP/CLEAR and call an authorized servicer for assistance.

Oven light does not work.

Replace or tighten bulb. See Changing Oven Light section in this Use & Care Guide.

 

 

 

 

 

Electrical power outage. Check house lights to be sure. Call your local electric

 

company for service.

 

 

 

Surface burners do not light.

Surface control knob has not been completely turned to LITE. Push in and turn the

 

 

surface control knob to LITE until burner ignites and then turn the surface control

 

knob to the desired flame size.

 

 

 

 

Burner ports are clogged. Clean burners. See “Cleaning the Burner Grates, Burner

 

Caps and Burner Heads” under General Cleaning.

 

 

 

 

Range power is disconnected from outlet. Be sure cord is securely plugged into the

 

outlet.

 

 

 

 

Electrical power outage.

 

 

 

 

Be sure the gas supply to the range is turned “ON”.

 

 

 

Surface burner flame burns half way

Burner ports or slots are clogged. With the burner off, use a small-gauge wire or

around.

needle to clean ports or slots.

 

 

 

 

 

Moisture is present after cleaning. Lightly fan the flame and allow the burner to

 

operate until flame is full. Dry the burners thoroughly following instructions under

 

General Cleaning.

 

 

 

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Before Setting Warranty 318203873 0703 Rev. aWelcome Before You CallWelcome & Congratulations Product RegistrationSerial Plate Location Questions?Important Safety Instructions For Your SafetyRemoving leveling legs, panels, wire covers, anti-tip What to do if YOU Smell GASImportant Instructions for Using Your Cooktop For Glass Cooktops only Grounding Instructions Conversion to Liquefied Petroleum Gas or L.P. GasFeatures At a Glance Setting Surface Controls Control Locations of the Gas Surface BurnersRemember do not Allow SPILLS, Food 5K or 14K 5K 12K or 16KFlame Size Type of Cooking Setting Proper Surface Burner Flame SizeOperating the Gas Surface Controls Before Setting Oven Controls Setting Oven ControlsAir Circulation in the Oven Arranging Oven RacksSetting Warm & Serve Drawer Control If Equipped Warm & Serve Drawer Temperature SelectionArranging Warm & Serve Drawer Rack Positions Operating the Warm & Serve DrawerCooking Informations Oven BakingBroiling Care & Cleaning Self-CleaningTo Set the Self-Clean Cycle Self-Cleaning OvenSurfaces How to Clean Stainless Steel some models Oven door & drawer front panelEasier into the rack positions Oven DoorCleaning the Cooktop, Burner Heads, Caps & Grates Allow SPILLS, FOOD, Cleaning Agents or ANY Other Material toRemoving and Replacing the Oven Door Hinge SlotRemoving and Replacing Storage Drawer To Remove and Replace Warm & Serve Drawer some modelsTo Remove and Replace Storage Drawer some models Adjusting Your Oven Temperature Place When the Oven is in USEChanging Oven Light To Replace the Light BulbBefore you call Self-cleaning cycle does not work Soil not completely removed after self- cleaning cycleSurface burner flame is orange Poor baking resultsMajor Appliance Warranty Information Exclusions

318203873 specifications

The Frigidaire 318203873 is an essential component designed to enhance the functionality of various Frigidaire ranges and ovens. This replacement part, known primarily as a dual burner element, is specifically tailored to deliver consistent heating and reliable performance, ensuring that everyday cooking tasks are performed with ease and efficiency.

One of the standout features of the Frigidaire 318203873 is its dual heating capability. This allows users to switch between two different power levels, providing flexibility when cooking a variety of dishes. Whether simmering sauces on low heat or boiling water rapidly on high, this element accommodates diverse culinary needs. The ability to choose between settings helps users achieve the desired temperature with greater precision, making meal preparation more effective.

Constructed with durability in mind, the Frigidaire 318203873 is built to withstand the high demands of daily use. The material used in its manufacturing is robust, ensuring longevity even under the rigors of continuous exposure to heat. This durability also translates into safety, as the design minimizes the risks of overheating and potential failure, contributing to a secure cooking environment for families.

Another characteristic that enhances the appeal of the Frigidaire 318203873 is its user-friendly installation process. Designed to fit seamlessly into compatible models, it allows for easy replacement without the need for extensive tools or technical knowledge. This ensures that users can restore their appliance's functionality quickly and effectively, minimizing downtime.

The element also showcases energy efficiency, an increasingly important feature in modern appliances. By optimizing power use while maintaining performance, the Frigidaire 318203873 helps reduce energy consumption. This is not only beneficial for household budgets but also contributes to a more environmentally friendly cooking experience.

In summary, the Frigidaire 318203873 dual burner element offers a combination of versatility, durability, and energy efficiency that makes it an indispensable addition to any Frigidaire range or oven. Its easy installation and reliable performance ensure that it meets the expectations of home cooks, from beginners to experienced chefs. With the 318203873, every cooking task is made simpler and more enjoyable, making it a valuable asset in any kitchen.
Top Page Image Contents