SLEEP
The sleep mode allows the system to continue to operate for a specified period of time before automatically shutting off.
Press the SLEEP button.
–The display shows the indication SLEEP 10.
–This means that the system will be switched to standby after 10 minutes.
–Each time the button is pressed, the setting is changed as below.
|
| 10 min 20 min | 30 min 60 min |
|
| |||
|
|
| OFF | 90 min |
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
Notes:
–During an active sleep timer period, you can reset the SLEEP time again by pressing the SLEEP button.
–A sleep timer period will be cancelled when you switch your system to standby (using the POWER button on your remote control).
RECORDING WITH A CASSETTE DECK
Select the desired input to be recorded.
Start recording on the cassette deck connected to TAPE MONITOR.
Start play on the desired input.
–For tape monitor function, refer to amplifier titled "TAPE MONITOR function".
DUBBING FROM VCR2 TO VCR1
Select VCR2 as program source to be recorded. Start recording on the VCR connected to VCR1. Start playback on the VCR connected to VCR2.
–For tape monitor function, refer to amplifier titled "TAPE MONITOR function".
When dubbing from VCR2 to VCR1, you can replace the audio signal from VCR2 with the signal from an audio source, e.g. a CD player.
First select VCR2 as program source to be recorded. Then select the required audio source.
Start recording on the VCR connected to VCR1.
Start playing back on the selected audio source and on the VCR connected to VCR2.
–You can now watch the picture from VCR2 on your TV and listen to the sound from the audio source while recording.
ADDITIONAL INFORMATION
|
|
|
|
|
MODEL |
|
|
| ENGLISH |
|
|
|
| |
POWER AMPLIFIER SECTION |
| |||
|
|
|
| |
|
|
|
|
|
POWER OUTPUT (8 Ohms) |
|
|
|
|
STEREO MODE | 90W x 2 |
|
|
|
|
|
|
|
|
THD | 0.05% |
|
|
|
IM DISTORTION | 0.05% |
|
|
|
POWER OUTPUT (8 Ohms) |
|
|
|
|
|
|
|
|
|
SURROUND MODE (LEFT, CENTER, RIGHT) | 80W x 3 |
|
|
|
REAR | 80W |
|
|
|
PREAMPLIFIER SECTION |
|
|
|
|
|
|
|
|
|
INPUT SENSITIVITY/IMPADANCE |
|
|
|
|
|
|
|
|
|
PHONO (47K Ohms) | 2.5mV |
|
|
|
LINE (CD, TAPE, VIDEO, @ 47K Ohms)) | 150mV |
|
|
|
|
|
|
|
|
SIGNAL TO NOISE RATIO |
|
|
|
|
|
|
|
|
|
PHONO | 77dB |
|
|
|
LINE (CD,TAPE,VIDEO) | 100dB |
|
|
|
|
|
|
|
|
TONE CONTROLS |
|
|
|
|
|
|
|
|
|
BASS (100Hz) |
|
|
| |
TREBLE (10kHz) |
|
|
| |
|
|
|
|
|
CINEMA BASS |
|
|
|
|
|
|
|
|
|
BASS @ 80Hz LEFT /RIGHT, CENTER |
|
|
|
|
FREQUENCY RESPONSE |
|
|
|
|
|
|
|
|
|
PHONO |
|
|
| |
LINE (CD, TAPE, VIDEO, |
|
|
| |
FM TUNER SECTION |
|
|
|
|
|
|
|
|
|
USABLE SENSITIVITY (MONO) | 10.5dBf |
|
|
|
50dB QUIETING SENSITIVITY |
|
|
|
|
MONO | 15dBf |
|
|
|
|
|
|
|
|
STEREO | 36.2dBf |
|
|
|
SIGNAL TO NOISE RATIO 65dBf,MONO/STEREO | 80dB/73dB |
|
|
|
THD @ 65dBf, 1kHz, MONO/STEREO | 0.15%/0.25% |
|
|
|
|
|
|
|
|
FREQUENCY RESPONSE |
|
|
| |
STEREO SEPARATION (1kHz) | 50dB |
|
|
|
CAPTURE RATIO | 1.25dB |
|
|
|
|
|
|
|
|
ALTERNATE CHANNEL SENSITIVITY ( @ 98MHZ, | 70dB |
|
|
|
IMAGE REJECTION RATIO | 80dB |
|
|
|
IF REJECTIOR RATIO | 120dB |
|
|
|
|
|
|
|
|
SPURIOUS REJECTION RATIO | 70dB |
|
|
|
AM TUNER SECTION |
|
|
|
|
USABLE SENSITIVITY (400u V/m) | 12.5uV |
|
|
|
|
|
|
|
|
SIGNAL TO NOISE RATIO | 50dB |
|
|
|
SELECTIVITY | 30dB |
|
|
|
DIMENSIONS and WEIGHTS (Unit) |
|
|
|
|
|
|
|
|
|
HEIGHT (INCHES) | 5 5/8 |
|
|
|
WIDTH (INCHES) | 17 3/8 |
|
|
|
DEPTH (INCHES) | 11 7/8 |
|
|
|
|
|
|
|
|
WEIGHT (LBS) |
|
|
|
|
Notes:
–Design and specifications subject to change without notice for improvement.
MAINTENANCE
Do not leave the unit in direct sunlight or other places where high temperatures can occur for any length of time, such as in the vicinity of a heating source.
Do not expose the equipment to humidity or rain.
A chamois leather cloth, slightly moistened with water is sufficient for cleaning the cabinet.
Do not use cleaning agents containing alcohol, spirits, ammonia or abrasive.
11