Maytag W10392923C warranty Troubleshooting, Oven Light, To Replace, Operation

The oven light is a standard 40-watt appliance bulb. Before replacing, make sure the oven and cooktop are cool and the control knobs are in the off position.

To Replace:

1.Unplug range or disconnect power.

Oven Light

2.Turn the glass bulb cover in the back of the oven counterclockwise to remove.

3.Turn bulb counterclockwise to remove from socket.

4.Replace bulb, then bulb cover by turning clockwise.

5.Plug in range or reconnect power.

TROUBLESHOOTING

First try the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)

to possibly avoid the cost of a service call.

www.maytag.com

Operation

PROBLEM	POSSIBLE CAUSES	SOLUTIONS
Nothing will operate	Power supply cord is unplugged.	Plug into a grounded outlet.
	Household fuse is blown or a	Replace the fuse or reset the circuit breaker. If the problem
	circuit breaker is tripped.	continues, call an electrician.
	Range is in Sabbath Mode.	See “Sabbath Mode” section.
Cooktop will not operate	The control knob is set	Push in knob before turning to a setting.
	incorrectly.

The range is in Demo Mode.

Demo Mode will deactivate the Warming Center element. See “Demo Mode” in the “Electronic Oven Controls” section.

Excessive heat around	Cookware that is not the proper
cookware on cooktop	size

Use cookware about the same size as the surface cooking area, element or surface burner. Cookware should not extend more than ½" (1.3 cm) outside the cooking area.

Cooktop cooking results not	Control knob set to incorrect heat	See “Cooktop Use” section.
what expected	level
	Range is not level.	Level the range. See the Installation Instructions.
Oven will not operate	The electronic oven control was	See “Electronic Oven Controls” section.
	set incorrectly.
	Delay Start was set.	See “Cook Time” section.
	The oven control lockout is set.	See the control lock keypad feature in the “Feature Guide”
		section.

The range is in Demo Mode.

Demo Mode will deactivate all heating elements. See “Demo Mode” in the “Electronic Oven Controls” section.

Convection fan not working	Oven door is open.	Close oven door. See “Convection Cooking” section.
Oven temperature too high or	Oven temperature calibration	See “Oven Temperature Control” in the “Electronic Oven
too low	needs adjustment	Controls” section.
	Temperature has been changed	See “Fahrenheit and Celsius” in the Electronic Oven Controls”
	to Fahrenheit or Celsius.	section.
Oven indicator lights flash	Needs service (oven indicator	See “Control Display” in the “Electronic Oven Controls”
	lights are flashing)	section. If the indicator light(s) keeps flashing, call for service.
		See cover for contact information.
Display shows messages	Power failure (display shows	Clear the display. On some models, reset the clock, if needed.
	flashing time)	See “Clock” keypad feature in the “Feature Guide” section.
	Error code (display shows letter	Press the CANCEL keypad to clear the display. See “Control
	followed by number)	Display” in the “Electronic Oven Controls” section. If it
		reappears, call for service. See cover for contact information.

Mineral deposits are left on the oven bottom after the Clean cycle

Tap water was used in the Clean cycle.

Use distilled or filtered water in the Clean cycle.

To remove deposits, use a cloth soaked with vinegar. Then use a cloth dampened with water to thoroughly remove any vinegar residue.

Range is not level.	Mineral deposits will collect on dry areas of the oven bottom
	during the Clean cycle. Level the range. See the Installation
	Instructions.
	To remove deposits, use a cloth soaked with vinegar. Then use
	a cloth dampened with water to thoroughly remove any vinegar
	residue.

16