Stanley Black & Decker HG80 manual Hose Types, Hose Safety Tags

Page 8

HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

 

 

 

 

 

 

 

 

 

 

 

 

A G

 

D A N G E R

 

 

 

 

 

 

D A N G E R

 

T

 

 

 

 

 

 

 

 

 

 

I S

 

1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

3.

DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE

 

H

 

WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN

 

 

 

 

 

 

OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.

 

T

 

DEATH OR SERIOUS INJURY.

 

 

 

 

 

 

KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT

 

VE

 

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-

 

 

 

 

 

 

CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION

 

 

 

 

 

 

 

 

AND SEVERE PERSONAL INJURY.

 

O

 

ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND

 

 

 

 

 

 

 

 

 

ELECTRIC LINES.

 

 

 

 

 

4.

HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR

 

M

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT

 

E

 

 

 

 

 

 

 

 

 

 

2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE

 

 

 

 

 

 

USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

R

 

 

 

 

 

 

 

 

 

ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-

 

 

 

 

 

5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-

 

T

 

 

 

 

 

 

 

 

TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND

 

 

 

 

 

 

 

 

 

 

 

 

 

AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE

 

N O

 

TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH

 

 

 

 

 

 

 

 

 

 

 

 

 

 

IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

 

 

SAFETY DEPARTMENT INSTRUCTIONS.

 

 

 

 

 

6.

 

D O

 

 

 

 

 

 

 

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

 

SEE OTHER SIDE

 

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SIDE 2

 

 

 

SIDE 1

 

 

 

 

 

 

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

D O N O T R E M O V E T H I S T A G

 

D A N G E R

 

 

D A N G E R

 

 

 

 

 

1.

DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS

5.

CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO

 

NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR

 

COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.

 

ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.

 

NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.

2.

FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY

6.

AFTER EACH USE STORE IN A CLEAN DRY AREA.

 

TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-

 

 

 

TRIC LINES.

 

 

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT

DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE

PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT

WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

 

 

SEE OTHER SIDE

 

 

 

 

 

SEE OTHER SIDE

 

 

 

 

SIDE 1

 

 

 

 

 

SIDE 2

 

 

 

(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

8 ► HG80 User Manual

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Hydraulic Grinder Page Table of Contents Safety Symbols Local Safety RegulationsSafety Precautions Grinding Wheel Safety Tool Stickers & Tags N G E RHose Safety Tags Hose TypesHose Recommendations Tool to Hydraulic Circuit Hose RecommendationsHtma / Ehtma Requirements Htma / Ehtma RequirementsPRE-OPERATION Procedures Operating ProceduresOperation Cold Weather OperationTool Protection & Care Troubleshooting Problem Cause SolutionSpecifications AccessoriesIllustration HG80 Parts List Part QTY DescriptionHG80 Parts List

HG80 specifications

Stanley Black & Decker HG80 is a powerful and versatile hot glue gun designed for both professional and DIY enthusiasts. This tool is celebrated for its efficiency and user-friendly design, making it ideal for a wide range of applications, from crafting and home repairs to industrial use.

One of the standout features of the HG80 is its dual-temperature system. Users can choose between high and low-temperature settings, allowing for maximum flexibility depending on the materials being bonded. The high-temperature setting is perfect for heavier materials like metals and ceramics, providing a strong and durable bond. In contrast, the low-temperature setting is ideal for delicate items such as lace, foam, or children's crafts, minimizing the risk of damage.

The HG80 boasts a quick heating time, reaching optimal temperatures in just a few minutes. This efficient heating mechanism ensures minimal waiting time, allowing users to start their projects promptly. Additionally, the glue gun has a built-in LED indicator that signals when it is ready for use, enhancing user convenience.

Another notable characteristic of the HG80 is its ergonomic design. The comfortable grip and lightweight construction enable users to handle the tool for extended periods without fatigue. This is especially beneficial for larger projects that require sustained use. The trigger mechanism is designed for precision application, giving users control over glue flow, which helps reduce wastage and supports detailed work.

Safety is a key focus for the HG80. It features a drip-resistant nozzle that prevents excess glue from leaking out while not in use. Coupled with a safety fuse, this ensures that the gun operates safely, minimizing the risk of overheating or accidental burns.

The HG80 is compatible with standard 0.43-inch glue sticks, making it readily accessible for users. The ability to use an array of glue sticks adds to its versatility, as different types can be selected based on the project requirements.

In summary, the Stanley Black & Decker HG80 hot glue gun is a feature-rich tool offering dual-temperature settings, rapid heating, ergonomic design, precision application, and safety features. These characteristics make it a reliable choice for anyone in need of a high-quality glue gun, whether for crafting, repair tasks, or professional projects. With its user-friendly nature and robust performance, the HG80 stands out as an essential tool for anyone looking to tackle adhesion tasks efficiently and effectively.
Top Page Image Contents