Black Box CMA DISHMACHINE manual Instructions

Page 17

 

QTY

P/N

DESCRIPTION

1

12 FT

00400.00

Conduit 3/8 sealtite

2

1

00401.00

ST-3/8 straight connector

3

1

00402.00

ST-90 deg.3/8 connector

4

2

00666.00

Fork tongue connector

5

24 FT

00529.00

Wire 18 gauge black

6

1

13427.60

Template kit

7

1

13427.61

Mounting bracket

8

1

13427.62

Actuator

9

1

13427.63

Bumper

10

2

03817.00

6-32 wing nut

11

2

03814.10

Lock star washer

12

2

00914.10

1/4-20 x 5/8 hexhead bolt

13

2

00968.00

1/4 split lock washer

14

2

00924.00

1/4 ss washer

15

2

00912.00

1/4-20 nylon lock nut

16

1

13427.10

Limit switch

Instructions:

1.Determine the approximate centerline of the dish rack as it travels down the clean table.

2.Place the template from the template kit (6) with the lower edge resting on the table surface, against the end roll, and centered along the dish rack’s line of travel. Mark the positions of the four holes and follow up with a center punch.

3.Drill a 1/8” hole through each position .The upper two holes then drilled out to1/2”.

4.Fasten the template with two bolts and nuts from the template kit (6).The lower holes then drilled out to 3/8”.

5.From the outside, place the mounting bracket (7) halfway through the 3/8” lower holes on the table and the hinged actuator (8) through two 1/2” upper holes in the table.

6.Secure the bumper (9) by tightening the two bolts (12) with lock washers (13) through the two holes in the actuator.

7.Push the mounting bracket all the way into the holes in the table and tighten it with two lock nuts (15) and two washers (14).

8.Attach the conduit (1) between the control box and the table limit switch (16). Run two wires (5) through the conduit and conduit connectors (2,3), and attach one to the COMMON terminal on table limit switch, and the other to the normally OPEN terminal, using two fork tongue connectors (4). Secure the table limit switch on the mounting bracket with two wing nuts (10). Remove jumper from the optional table limit switch connection in the control box (see note 1 of the wiring diagram). Then, attach the other ends of the two wires to the terminal block (it does not matter which table limit switch wire you attach to either terminal because it is only a loop).

MODEL CMA-66 Part Manual rev. 1.06 01/11/05

Page 18

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Model CMA-66 Table of Contents Parts Manual Exploded View Drawings Cabinet AssemblyControl Box Assembly Curtain and Optional Vent System Temperature Control System Pump Assembly Drain System Assembly Plumbing System Assembly Wash System assembly Rocker Arm Assembly Trip Switch Assembly Old Style Trip Switch Assembly New Style Paddle Switch Assembly Table Limit Switch Instructions P/N Instructions Corner Feed Table Optional factory installed only Model CMA-66 Part Manual rev .05 01/11/05 Page20 Drain Water Tempering Kit Optional

CMA DISHMACHINE specifications

The Black Box CMA DISHMACHINE is a versatile and high-performance dishwashing solution designed to meet the demanding needs of commercial kitchens and food service operations. Known for its reliability, efficiency, and advanced features, this machine stands out in the competitive landscape of professional dishwashers.

One of the main features of the Black Box CMA DISHMACHINE is its impressive cleaning capacity. With the capability to wash up to 30 racks per hour, it ensures that large volumes of dishes, glasses, and utensils are quickly sanitized, allowing kitchen staff to focus on food preparation and service. Its high-temperature wash cycle effectively removes tough grease and food residues, providing exceptional cleanliness.

The machine is equipped with intuitive digital controls that simplify operation. Users can easily select washing cycles, adjust temperatures, and monitor performance through a user-friendly interface. The advanced control panel also features diagnostic capabilities that provide real-time information about the machine's status, enabling quick troubleshooting and maintenance.

Built with durability in mind, the CMA DISHMACHINE boasts a robust stainless-steel construction, making it resistant to corrosion and wear. This design choice not only extends the life of the machine but also ensures a hygienic environment by minimizing bacterial growth. Moreover, the dishwasher's compact dimensions make it a fitting solution for kitchens with limited space while still offering an ample washing capacity.

Energy efficiency is another hallmark of the Black Box CMA DISHMACHINE. Its state-of-the-art technology reduces water and energy consumption without compromising on performance. This feature not only contributes to lower operational costs but also aligns with eco-friendly practices increasingly adopted in modern kitchens.

Additionally, the CMA DISHMACHINE integrates smart technologies such as an automatic detergent dispenser and deliming system. These innovations ensure optimal cleaning results with minimal operator intervention, allowing staff to focus on other essential kitchen operations.

In conclusion, the Black Box CMA DISHMACHINE is a top-tier dishwashing solution equipped with features that promote efficiency, durability, and ease of use. Its high-capacity performance, advanced control systems, and energy-saving technologies make it an invaluable asset for any busy kitchen looking to enhance productivity and maintain high hygiene standards.
Top Page Image Contents