Introduction, Parts included, Preparation

Introduction

1 Introduction

1.1 Parts included

Vent Hood Kit

•1 - 4” vent hood: VH1-4

•4 - Exterior screws

•1 - 5” to 4” vent reducer pipe

•1 - AQ4FLAPPER back draft accessory

Vibration Mount Packet

•2 - Vibration mounts with nuts and washers

•2 - Brackets with nuts and washers

Flow Switch Packet

•1 - Flow switch

•4 - Replacement pipes (See chapter 2.7)

•2 - Pipe clips

•1 - Molex connector cable

•1 - Heat exchanger bushing

Power vent motor

•1 - Power vent motor (HSUL-1 Series containing integrated 24v control circuit) including 25 foot control cable with wire nuts and an HPN 6-foot power cord

•5 - Nylon ties

1.2 Warnings

1.Failure to install, maintain and/or operate the power vent in accordance with manufacturer’s instructions may result in conditions which can produce bodily injury and property damage.

2.The power vent must be installed by a qualified installer in accordance with all local codes or, in their absence, in accordance with the National Fuel Gas Code (ANSI Z223.1 NFPA #54), the National Electric Code, the Canadian Electrical Code (C22.1), Canadian Gas Code (CSA B149.1) and The Occupational Health and Safety Act (OSHA) as applicable.

3.The power vent motor shaft must be mounted horizontally to prevent motor bearing wear.

4.Disconnect power supply when making wiring connections or when working around the fan blade and motor. Failure to do so may result in severe personal injury and equipment damage.

5.Make certain the power source is adequate for the fan motor requirements. Do not add the power vent to a circuit where the total load is unknown.

AQ4 Motor is 200 watts- 1.66 amps @ 120vac.

6.Locate the outlet receptacle as close to the vent motor as possible. Do not use an extension cord.

Warning: Failure to install AQ4FLAPPER properly may allow freezing air to come in contact with the water heater’s heat exchanger and cause the heat exchanger to burst. Such damage is not covered under the water heater’s warranty.

1.3 Preparation

1.Follow installation and operating instructions manual supplied with the water heater.

2.Before mounting water heater to wall, check its minimum clearance requirements.

3.When using an AQ4 the maximum vent length from the water heater to the point of termination is 25 feet with one elbow. Subtract 5 feet for each additional 90° elbow (up to two additional elbows allowed.)

4.Install power vent motor as close to the vent hood

AQ4 Manual

AQ4 specifications

AquaStar AQ4 is a cutting-edge water filtration system designed to provide clean and safe drinking water for households and businesses. This innovative product stands out in the market with its advanced technology and user-friendly features, making it a top choice for those seeking high-quality water purification.

One of the main features of the AquaStar AQ4 is its multi-stage filtration process. The system employs a series of filters that work together to remove a wide range of contaminants from water. This includes sediment, chlorine, heavy metals, and microorganisms. The first stage is a sediment filter that captures larger particles, while subsequent filters target smaller impurities. This comprehensive approach ensures that the water is not only clear but also free from harmful substances.

The AquaStar AQ4 utilizes activated carbon technology, which is renowned for its effectiveness in removing odors and improving taste. The activated carbon filter absorbs chemicals and volatile organic compounds (VOCs), resulting in crisp and refreshing drinking water. Additionally, the system features a reverse osmosis membrane, which acts as a barrier, allowing only pure water molecules to pass through while blocking contaminants.

Another impressive characteristic of the AquaStar AQ4 is its smart monitoring system. It is equipped with sensors that track filter performance and water quality in real time. Users receive alerts when it is time to replace filters, ensuring optimal performance at all times. This intelligent feature not only simplifies maintenance but also enhances the longevity of the system.

Installation and operation of the AquaStar AQ4 are straightforward, catering to both DIY enthusiasts and those who prefer professional assistance. The compact design allows it to fit seamlessly under most kitchen sinks, saving valuable space. Moreover, the system operates quietly, making it suitable for residential or commercial use without causing disturbances.

In addition, the AquaStar AQ4 is environmentally friendly. By reducing the reliance on bottled water, it contributes to decreasing plastic waste. The system’s durable filters are designed to provide long-lasting performance, reducing the frequency of replacements and promoting sustainability.

In conclusion, the AquaStar AQ4 is a robust water filtration solution that combines advanced technology with user-friendly features. Its multi-stage filtration process, activated carbon technology, smart monitoring system, and environmental benefits make it an excellent choice for anyone seeking quality water purification. With the AquaStar AQ4, users can enjoy peace of mind knowing that they have access to safe and great-tasting water at all times.