Moyer Diebel MD-66, MD-44 operation manual Chemical Signal Connections, Vent Fan Signal Connection

Page 22

Installation

Chemical Signal Connections

1.Use a qualified detergent/chemical supplier for detergent/chemical and dispensing equipment needs.

2.Labeled detergent control circuit connection terminals are provided in the control cabinet for detergent and rinse agent/sanitizer dispensing equipment (supplied by others).

3.The illustration at right, shows the terminal board for the machine.

4.The signal connection points include:

Detergent signal 120VAC, 1A max load.

Rinse aid/Sanitizer signal 120VAC, 1A load.

5.A removable black plug is provided in the load end side of the wash tank for installation of the detergent conductivity cell.

Vent Fan Signal Connection

SIGNAL ONLY

VENT FAN

120V

COMMON

RINSE AID

120V

COMMON

DETERGENT

120V

NOTE:

The Vent Fan Signal Connection supplies 120VAC to a control relay (supplied by others) when the dishwasher is ON and O VAC when the dishwasher is OFF. Power to operate the vent fan (supplied by others) must be supplied separately.

6.The Vent Fan signal connection point is located on the same terminal board as the chemical connections (see illustration above). The connection is:

• Vent Fan 120VAC, 1Amp max amp load

Running Signal and

Table Limit Switch Connections

7.Connections are provided for systems that require a signal to indicate the dishwasher is running.

8.A signal connection is provided to indicate that the dishwasher has stopped due to a conveyor jam or when the clean dish table is full of racks and additional racks cannot exit the machine.

9.The table limit switch option installation is recommended for all dishwashers and can be ordered from the factory by P/N 407400.

SIGNAL ONLY

MACHINE

RUNNING

TABLE

LIMIT

SWITCH

14

Image 22
Contents Manual P/N 114725 rev. a National Service Department Business Reply Mail Important Important Revision History Limited Warranty MD-44 and MD-66 Rack Conveyor Dishwashers  Model Descriptions Model MD-44Receiving MD-44 Direction Field Conversion Parts Needed for Conversion Supplied by OthersOn next MD-44 Direction Field Conversion MD-44 Direction Field Conversion 10A 46-1/2 Changing Wire Connections in the Lower Junction Box MD44 Junction BOX Wiring Diagram Utilities Hot Water ConnectionsDrain Connections Ventilation ConnectionsElectrical Connections Machine Electrical Connection PlateGRD Vent Fan Signal Connection Chemical Signal ConnectionsRunning Signal Table Limit Switch Connections Curtain Locations Door Safety Switches Pump Intake Screen and Dual Float SwitchScrap Screens Installing the Lower Spray arm Assembly Installing the Upper Spray Arm Assembly Upper Wash Arm AssemblyGuide Pin Upper Wash ArmInstallation Installing the Pawl Bar Installing the Curtains Check list Power Switch Control Panel OperationOperation Do not Overload RacksCleaning RingDe-liming At the End of the DayMaintenance WeeklyCondition Cause Solution Service Replacement Parts Control Panel Decal 36 Control Cabinet 3-HOLE, PW-W-R HOUSING, SwitchCOVER, Control Cabinet PUSHBUTTON, RED SquareCabinet Control Cabinet Extended Vent Cowls Splash SHEILD, Vent 8 Extended Wash Tank Door, Panels and Curtains PANEL, END, Full MT-RACK ROD, CurtainGUIDE, U-CHANNEL, Door 14 329985 BRACKET, Water DiverterWash Tank Heat, Float Switch, and Scrap Screens WASHER, Spacer WASHER, Flat SSTClip 16 107440 THERMOMETER, 8 FT. FlangedWash Tank Junction Box Terminal Block TERMINAL, Single ST 2.5 Gray TERMINAL, SINGLE, ST 2/5 WH WhiteTERMINAL, Double Sttb TERMINAL, SINGLE, ST 2.5 BU BlueMD-66 Prewash Tank, Door and Curtains 11 110854 Float SWITCH, Rack Machine 24 329985 BRACKET, Water DiverterFill Piping 13 102388 BUSHING, Reducing 1/2 NPT X 1/4 NPT Brass NIPPLE, 3/4 NPT X Close Brass12 207082 TUBE, Booster OUTLET, 45 L-R Direction 900837 KIT, Repair Vacuum Breaker 3/4Final Rinse Piping Wash ARM Oring GASKET, Rinse MANIFOLD, 3/4 PipingNOZZLE, VEE-JET #8003 PLUG, E Final Rinse ManifoldMD-66 Prewash Spray Arms Manifold Taper ASSY. Upper Wash HEX Acorn Plain NUT, 1/4-20 SSTRing Standpipe WELDMENT, 1-1/4 OD MD66MD-44, MD-66 Wash Spray Arms Threaded PLUG, Wash ARM Manifold Taper ASSEMBLY, UpperGASKET, HEATER/STANDPIPE 13 333096 Standpipe Weldment 44 MT-RACK118 SWITCH, Reed Aleph MAGNET, Reed SwitchPIN, Idle Pump Switch PLATE, Track Adjustment MD-RACKMD-66 Track Assembly MAGNET, Reed Switch 10 327833 PIN, Idle Pump Switch 12 333082 Track WELDMENT, Front 44 MT-RACKMD-44 Pawl Bar Assembly 17 113714 Ring RETAINING, 3/8 OD Shaft PAWL, CradleCROSSHEAD, Pawl BAR HEX Acorn Plain NUT, 10-32 SSTMD-66 Pawl Bar Assembly 22 333643 CHANNEL, Drive Support PW 66 MT-RACK 167 SHEAVE, Motor AK51 Drive Motor SwitchBRACKET, Motor Switch Mounting PLATE, Drive Motor MountingConveyor Drive Assembly Roller STUD, Crosshead HOUSING, BEARING/SEALROLLER, Crosshead CRANK, Rack ARMPump/Motor Assembly Pump Seal Assembly PUMP/MOTOR Assembly Includes ItemsIMPELLER, 3.78 OD, Composite MTL Wash CLAMP, Hose M52 SST Gear Type Rewash Wash Qty Electric Booster Assembly 40F and 70F Rise To Final Rinse Electric Booster Assembly 40F and 70F Rise 1417 CAP, 3/4 NPT SST TEE, 1-1/2 NPT GalvanizedNIPPLE, 1-1/2 NPT X CLOSE, Galvanized PLUG, 3/4 NPT SQ. HD., BrassMD-66 Drain Asssembly Direction Shown 25 114817 Sleeve BEARING, 1/2 DIA. ROD Nylon 12 104165 CLAMP, Hose M40 SST GEAR-TYPE21 111034 Drain BODY, Machined Nipple TOE, 1-1/2 NPT X 6 LG. GalvDish racks RACK, PEG RACK, CombinationThis Intentionally Left Blank Rack Control Module Operation Electrical Schematics Module Rack Control Module RCM Operation Output Section Green Indicator Lights Rack Control Module RCM OperationRCM Status/Jumpers Rack Control Module RCM Indicator Lights Normal Operation SequenceDoors closed Rack switch Door Opened while Dishwasher is In-cycle RUN Light OFF RUN Light OFF JAM Switch OFFRUN Light ON. JAM Switch on RUN Light onLower Floats UP ALL Floats DownUpper Floats UP OFF Lights OFFPage Page Page This Intentionally Left Blank

MD-44, MD-66 specifications

Moyer Diebel has established a reputation as a leader in the commercial dishwashing industry, known for producing technologically advanced and reliable machines. Among their popular models are the MD-66 and MD-44, both designed to meet the needs of high-volume establishments. These machines exemplify Moyer Diebel's commitment to quality and efficiency.

The MD-66 is an energy-efficient dish machine suitable for large restaurants, hotels, and institutional kitchens. With a capacity to wash up to 66 racks per hour, it significantly speeds up the dishwashing process, making it ideal for busy environments. Its unique design features a dual rinse system that ensures consistent and thorough cleaning, while its adjustable wash cycles allow operators to customize the washing intensity based on the type of load – whether heavily soiled pots or delicate glassware.

Equipped with advanced technology, the MD-66 incorporates a microprocessor control system, providing users with real-time feedback on machine performance and diagnostics. This feature helps facilitate preventive maintenance, reducing downtime, and ensuring operational efficiency. The built-in energy efficiency measures contribute to lower utility costs, making this machine not only effective but also environmentally friendly.

Similarly, the MD-44 is designed for smaller establishments that still demand high efficiency. With a capacity of 44 racks per hour, it strikes a balance between compact design and powerful performance. This machine is particularly appealing for cafes, small restaurants, and catering operations. The MD-44 shares many features with the MD-66, including adjustable wash cycles and a robust rinse system, ensuring that even smaller operations receive the same level of cleanliness and hygiene.

Both the MD-66 and MD-44 utilize advanced spray technology, providing optimal water distribution to maximize cleaning effectiveness while minimizing water usage. The user-friendly interfaces on both models simplify operation, ensuring that staff can quickly learn to use the machines without extensive training.

In summary, Moyer Diebel’s MD-66 and MD-44 dishwashing machines combine high capacity, innovative technology, and efficiency to meet the varying needs of different sizes of commercial kitchens. Their robust designs and advanced features make them reliable investments for any foodservice establishment seeking to streamline their dishwashing processes while maintaining the highest standards of cleanliness and performance. These models reflect Moyer Diebel's focus on quality engineering, customer satisfaction, and environmental responsibility.