Troubleshooting
Whenever the appliance fails to work, check for a solution from the following list before calling for Assistance
(see Assistance). |
| EN | |
|
| ||
|
|
|
|
| Problem: | Possible causes / Solutions: |
|
|
|
|
|
| The dishwasher does not start | • Switch off the appliance by pressing the ON/OFF button, switch it back on after |
|
| or cannot be controlled | approximately one minute and reset the program. |
|
|
| • The appliance has not been plugged in properly. |
|
|
| • The dishwasher door has not been shut properly. |
|
|
|
|
|
| The door won’t close | • The lock was released. Strongly push the door until a “clacking” noise is heard. |
|
|
|
|
|
| No water drains out from the | • The dishwasher cycle has not yet finished. |
|
| dishwasher. | • The water inlet hose is bent (see Installation). |
|
|
| • The drain duct is blocked. |
|
|
| • The filter is clogged up with food residues. |
|
|
|
|
|
| The dishwasher makes | • The dishes are rattling against each other or against the sprayer arms. |
|
| excessive noise. | • An excessive amount of foam has been produced: the detergent has not been |
|
|
| measured out correctly or it is not suitable for use in dishwashers (see |
|
|
| and use). |
|
|
|
|
|
| The dishes and glasses are | • The level of the refined salt is low or the dosage setting is not suited to the |
|
| covered in a white film or | hardness of the water (see Rinse aid and salt). |
|
| limescale deposits. | • The lid on the salt dispenser is not closed properly. |
|
|
| • The rinse aid has been used up or the dosage is too low. |
|
|
|
|
|
| The dishes and glasses are | • The rinse aid dosage is too high. |
|
| streaked or have a bluish tinge. |
|
|
|
|
|
|
| The crockery has not been | • A wash cycle without a drying program has been selected. |
|
| dried properly. | • The rinse aid has been used up or the dosage is too low (see Rinse aid and salt). |
|
|
| • The rinse aid dispenser setting is not suitable. |
|
|
| • The crockery is made from |
|
|
|
|
|
| The dishes are not clean. | • The racks are overloaded (see Loading the racks). |
|
|
| • The crockery has not been arranged well. |
|
|
| • The sprayer arms cannot move freely. |
|
|
| • The wash cycle is too gentle (see Wash cycles). |
|
|
| • An excessive amount of foam has been produced: the detergent has not been |
|
|
| measured out correctly or it is not suitable for use in dishwashers (see |
|
|
| and use). |
|
|
| • The lid on the rinse aid compartment has not been shut correctly. |
|
|
| • The filter is dirty or blocked (see Care and maintenance). |
|
|
| • The refined salt level is low (see Rinse aid and salt). |
|
|
|
|
|
| The dishwasher does not take | • There is no water in the mains supply. |
|
| any water in/Tap | • The water inlet hose is bent (see Installation). |
|
|
| • Turn on the tap and the appliance will start after a few minutes. |
|
| (the Drying and End indicator | • The appliance is locked because no action was taken when the indicator lights |
|
| lights flashes). | were flashing. Switch off the machine using the ON/OFF button, turn on the tap |
|
|
| and switch the machine back on after 20 seconds by pressing the same button. |
|
|
|
| |
|
|
|
|
| Water inlet hose alarm/Water | • Switch off the appliance by pressing the ON/OFF button. Shut off the water tap to |
|
| inlet filter blocked. | eliminate the risk of flooding and remove the plug from the electrical socket. Make |
|
| (the Washing, Drying and End | sure the water inlet filter has not become blocked by various impurities. (see “Care |
|
| indicator lights flashes). | and maintenance” chapter). |
|
|
|
|
|
*Only available in selected models.
13