Jura Capresso IMPRESSA X9 Cleaner for Press KEY, Machine Clea, Water for C Press KEY, Clean NOW

16.8 General cleaning instructions

Never use sharp objects or caustic chemicals for cleaning.

Clean the inside and outside of the case using a soft, damp cloth.

Clean the pivoting steam spout (V) each time it was used.

After heating milk, draw off some steam to clean the inside of the pivoting steam spout (V).

The water tank should be rinsed out and filled with fresh water daily.

Visible calcification in the water tank can be removed using a commercial decalcifying agent. Take out the water tank (Fig.2).

If you are using a CLARIS plus filter cartridge, remove it before decalcifying the tank.

16.9 Disassembling and cleaning the dual spout

We recommend to disassemble and clean the dual spout if you make milk products regularly.

Remove the cover of the height-adjustable dual spout by pressing the Unlock key (Fig. 12) and remove the coffee distributor (Fig. 13).

Take off the spouts (Fig. 13).

Take the spouts apart (Fig. 14).

Thoroughly rinse all the parts with warm water.

Reassemble the parts (Fig. 14).

When assembling the dual spout, note the colour of the indi- vidual parts (Fig. 14).

Attach the spouts to the IMPRESSA X9 (Fig. 13).

Put back the cover, making sure it locks into place (Fig. 13).

Use corresponding brushes for carrying out the cleaning steps described in sections above.

16.10 Cleaning the milk system

We recommend to clean the milk system daily.

Once started, the cleaning process must not be interrupted. It takes approx. 2 minutes.

Open the programming door on the front (Fig. 4).

Press the Clean Milk System key (Fig. 5/H) until you hear an acoustic signal.

CLEANER FOR

PRESS

KEY

Place a receptacle with a capacity of at least 0.5 litres under the height-adjustable dual spout (Fig. 6).

Fill a receptacle with approx. 4 dl of water and add 1 1/2 capfuls of JURA cappuccino cleaning agent. Dip the two milk hoses into this solution (Fig. 8/B).

Press the Clean Milk System key (Fig. 5/H).

MACHINE CLEA

You will hear an acoustic signal.

WATER FOR C

PRESS

KEY

Fill a receptacle with approx. 4 dl of fresh water and dip the milk hoses into it (Fig. 8/B).

Press the Clean Milk System key (Fig. 5/H).

MACHINE CLEA

COFFEE READY

Always dip both milk hoses into the fluid (Fig. 8/B).

16.11 Cleaning the coffee system

Once started, the cleaning process must not be interrupted. It takes approx. 15 minutes.

COFFEE READY

CLEAN

After having dispensed 220 products or after 80 rinsing cy- cles, the machine must be cleaned. The machine will still make coffee or hot water/steam. However, we recommend that you run a cleaning cycle within the same day. After hav- ing made another 20 coffees the cleaning alarm flashes, and after yet another 20 coffees, the display will indicate the fol- lowing message:

CLEAN NOW

Open the programming door (Fig. 4) and press the Clean Coffee System key (Fig. 5/I) until you hear an acoustic signal.

EMPTY

TRAY

EMPTY

COFFEE

BIN

Remove the tray and the grounds bin and EMPTY the coffee grounds.

COFFEE BIN

MISSING

Place the grounds bin and the tray back into the machine.

PRESS

KEY

Place a sufficiently large receptacle under the height-adjustable dual spout (Fig. 6).

Press the Clean Coffee System key (Fig. 5/I) until you hear an acoustic signal.

MACHINE CLEA

You will hear an acoustic signal.

ADD TABLET

PRESS

KEY

Drop an original JURA cleaning tablet into the filler funnel (Fig. 16).

Press the Clean Coffee System key (Fig. 5/I).

MACHINE CLEA

You will hear an acoustic signal.

EMPTY

TRAY

EMPTY

COFFEE

BIN

Remove the tray and the grounds bin and EMPTY the coffee grounds.

COFFEE BIN

MISSING

14