RT-1082 DAB/AM/FM Stereo Tuner
A Few Precautions
Please read this manual carefully. In addition to installation and operating instructions, it provides valuable information on various RT-1082 system configurations as well as gen- eral information that will help you get optimum performance for your system. Please contact your authorized Rotel dealer for answers to any questions you might have. In addition, all of us at Rotel welcome your questions and comments.
Save the RT-1082 packaging material for future use. Shipping or moving the RT-1082 in anything other than the original packaging material may result in severe damage that is not covered by the warranty.
Register online at www.rotel.com/register and keep your original sales receipt. It is your proof of purchase in the event that warranty service is required.
Key Features
6
Placement
Place the RT-1082 on a solid, dry, level surface away from direct sunlight, excessive heat, high humidity or strong vibrations. The RT-1082 can generate some heat during normal operation. If installed in a cabinet, make sure that there is adequate ventilation. Make sure there is enough room behind the RT-1082 for easy hookup. Place the unit close to the other components in your audio/video system and, if possible, place it on its own shelf. This will make initial cable routing, hookup, and any subsequent system changes easier. It also minimizes potential interference or heat buildup from other components.
Don’t stack heavy objects on top of the RT- 1082. Do not expose the unit to moisture; this could damage the circuitry and cause a safety hazard.
Rear Panel Connections
AM Loop Antenna u
The RT-1082 includes a loop antenna to receive AM radio signals. Remove this antenna from the box and locate it near the RT-1082.
Connect the 300 ohm twin-conductor wire from the loop antenna to the pair of screw terminals labeled AM LOOP, attaching one wire to each terminal. It does not matter which wire attaches to which terminal, but make sure that the connections are solid and that the two wires do not touch
You may need to rotate or otherwise reorient the antenna to find the best position.
NOTE: To use an outdoor antenna, connect its 300 ohm twin-conductor wire to the G and AM terminals in place of the loop an- tenna, only after a professional contractor has installed the antenna system in accor- dance with local electrical codes.
•AM, FM and DAB tuning capabilities.
•User-friendly Fluorescent Display.
•30 Station Presets for memorizing your favorite AM/FM stations; 99 presets for DAB stations.
•Manual frequency and preset tuning, auto-search tuning, preset scanning and frequency direct tuning.
•RDS (Radio Data System) capability for Europe and RBDS (Radio Broadcast Data Service) capability for the USA.
•DAB (Digital Audio Broadcast); a digital transmission available throughout Europe and Canada as well as many other sup- ported regions.
•Stereo/mono switching.
•12-volt trigger connections for remote turn on/off by Rotel preamplifiers and surround processors.
•Full- function wireless remote control.
Unpacking
Remove the unit from its packing. Look for the handheld remote control and other ac- cessories. Install the supplied batteries in the remote control. Save the packing and box as it will protect the RT-1082 if you move or need to return it for maintenance.
The RT-1082 provides rear panel connections for audio line level output, an FM antenna, an AM antenna, a DAB antenna, a 12V Trigger, a remote IR sensor, DAB digital outputs and AC power input.
NOTE: Do not plug any system component into an AC source until system hookup is complete and you are confident that all component-to-component connections have been properly made.
FM Antenna y
The RT-1082 is supplied with a T-shaped indoor FM antenna. Remove this antenna from the box and connect its attached coax F-type plug to the FM antenna connector on the RT-1082. For best reception, unfold the T-shaped antenna. Eyelets at both ends of the T allow tacking the antenna to a wall if desired. Experiment with positioning for best reception.
NOTE: To use an outdoor antenna, connect its 75 ohm coax lead wire to the FM con- nector in place of the indoor wire antenna, only after a professional contractor has in- stalled the antenna system in accordance with local electrical codes. In the USA, you will need to use the supplied F-type convert- er to connect the 75 ohm coax cable to the antenna input.
DAB Antenna i
Included is a DAB indoor antenna. If you cannot obtain good reception using this sup- plied antenna, it is recommended to use an outdoor DAB antenna. The outdoor antenna can be connected with a F-Type connector (male) then to the “Antenna DAB” connection on the rear panel.
RCA Outputs o
Line level RCA audio outputs send a fixed- level stereo signal from the RT-1082 to your pre-amplifier, system controller, or integrated amplifier.
Use a standard RCA audio cable to connect the LEFT OUTPUT jack to the left channel tuner input on your system controller and the RIGHT OUTPUT jack to the right channel tuner input on your system controller.
DAB Digital Outputs p
One coaxial and one S/PDIF output capable of outputting available DAB (Digital Audio Broadcast) stations. DAB provides interference free, near CD quality audio as well as any corresponding broadcast data.
