Toro 1116-080-A, 1133-080-A, 1132-080-A1 TRANSFORMER, Burner Replacement, Oven Control Replacement

Page 22

F. Reassemble in reverse order and check system operation. Be sure capillary tube is securely in the mount.

NOTE: Push reset button on new thermostat.

TRANSFORMER, BURNER – REPLACEMENT

A.Shut off power at main breaker.

B.Remove conveyor and front control box cover.

C.Remove all wires from transformer and mark for reassembly.

D.Remove two mounting screws from transformer base and remove transformer.

E.Reassemble in reverse order and check system operation.

OVEN CONTROL – REPLACEMENT

A.Shut off power at main breaker.

B.Remove conveyor and front control box cover.

C.Remove all wiring connections and mark for reassembly.

D.Remove oven control by pulling control from the mounting pins. Remove control from oven.

E.Before installing new oven control, set voltage jumper (located at the bottom center of the oven control) to the proper voltage (120V/240V) position. Set frequency jumper to the proper frequency (50Hz/60Hz). Install the four pushbutton extensions (included with the oven control) by pushing the extensions onto the four set buttons on control.

F.Reassemble in reverse order and check system operation.

G.Set the oven control for the proper operating mode. The 1100 series ovens use a single temperature control system. The oven control must be set to the proper operating mode. Set the control as follows: With the oven power switch “off”, depress the “time” and “up” buttons and turn the oven “on”. Control will indicate ”Imp I or Imp II” Release the buttons, The control will indicate “Temp to store”. Press the “up” or “down” button until “Imp II” appears on the display. Press the “temp” button. The control is now set for single burner operation.

TRANSFORMER – CONTROL – REPLACEMENT

See “TRANSFORMER –BURNER - REPLACEMENT

THERMOCOUPLE – REPLACEMENT

A.Shut off power at main breaker.

B.Remove conveyor and bottom finger assembly.

C.Remove front control box cover.

D.Remove thermocouple from bracket in oven chamber and pull thermocouple through tube into control box.

E.Remove two thermocouple wires from temperature control. Note wire color and location for reassembly

F.Reassemble in reverse order and check system operation

THERMOCOUPLE MEASUREMENT

TEMPERATURE (°F)

D.C. MILLIVOLTS

200°

2.8

250°

4.0

300°

5.1

350°

6.0

400°

7.1

450°

8.2

500°

9.3

550°

10.4

600°

11.5

22

Impinger II – Advantage Digital Express Service Manual - Domestic

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Impinger Conveyor Ovens NAT. GAS Power SupplyTemperature Control LP GASPhase Automatic Cool DownSchematic Diagram Model 1130-080-A, 1130-080-A1, 1131-080-A, 1131-080-A1 Model 1132-080-A, 1132-080-A1, 1133-080-A, 1133-080-A1 Model 1161-080-A Model 1162-080-A Model 1130-08H-A, 1131-08H-A Model 1132-08H-A, 1133-08H-A Troubleshooting Guide GAS Ovens Symptom Possible Cause EvaluationMain fan motor to neutral. If no voltage is Occur. If flame is not detected, the ignition control will With Power on and Thermocouple Needed Troubleshooting Guide Electric Ovens Page Control Closed position. If there is no voltage to REMOVAL, Installation and Adjustments MOTOR, Main FAN ReplacementFuse Holder Replacement Capacitor ReplacementON/OFF Switch Replacement Cooling FAN, Control BOX ReplacementTransformer Control Replacement TRANSFORMER, Burner ReplacementOven Control Replacement Thermocouple ReplacementTemperature Regulation Valve Replacement Burner Control ReplacementGAS Valve Replacement HOT Surface Igniter ReplacementReversing Switch Replacement Bypass Orifice ReplacementMain Burner Orifice Replacement Conveyor Drive Motor ReplacementMercury Contactor Replacement BEARING, Conveyor ReplacementHeating Element Replacement General View Impinger II Advantage Model Letter Part Number DescriptionGeneral View Control BOX, Front Model 1116-080-A, 1116-080-A1, 1117-080-A, 1117-080-A1Control BOX, Front View Model Control BOX, Front Model Control BOX, Front View Model Control BOX, Rear Model Control BOX, Rear View Model Control BOX Rear Model Control BOX, Rear View Model Oven Back Assembly Oven Back Assembly View Conveyor / Door Conveyor / Door View

1117-080-A1, 1117-080-A, 1130-080-A, 1131-080-A, 1132-08H-A specifications

The Toro 1133-080-A, 1132-080-A1, TRUE, 1130-080-A1, and 1132-080-A represent an innovative range of irrigation components designed to efficiently manage water distribution for both residential and commercial landscaping applications. These products stand out in the horticultural and agricultural sector due to their commitment to sustainability, flexibility, and user-friendliness.

One of the main features of the Toro 1133 series is its advanced water-saving technology, which allows users to optimize water usage effectively. This technology not only promotes conservation but also reduces water bills, making it an economical choice for users. The precision-engineered nozzle designs of these models ensure that water is delivered exactly where needed, minimizing waste and promoting healthy plant growth.

The Toro 1132 series shines with its durable construction. Designed to withstand the rigors of outdoor conditions, these components are made from high-quality materials that resist wear and tear over time. This durability is essential for users seeking long-term solutions for their irrigation needs.

Additional conveniences are integrated into the design of the Toro 1130-080-A1 and 1132-080-A models. They come equipped with easy-to-install features, making the installation process straightforward, even for those without extensive experience in irrigation systems. The user-friendly design enhances accessibility, allowing homeowners and landscapers alike to set up their watering systems with minimal effort.

Another characteristic that sets these models apart is their adaptability. Whether used in residential gardens, commercial landscapes, or agricultural applications, the Toro irrigation components can easily be adjusted to fit various layouts and watering needs. This versatility makes them suitable for a wide range of environments, ensuring that every landscape receives the irrigation it requires for optimal growth.

Lastly, the Toro brand is synonymous with innovation and excellence in irrigation technology. By choosing any of the Toro 1133-080-A, 1132-080-A1, TRUE, 1130-080-A1, or 1132-080-A systems, users can trust they are utilizing products backed by years of research and development, supported by a reputation for reliability and quality in the industry. These models not only embody the latest in irrigation technology but also reflect a dedication to eco-friendly practices, helping users achieve lush, thriving landscapes while contributing to water conservation efforts.
Top Page Image Contents