CHECK | INSTALLATION | DIMENSIONS |
|
A. Disposer Height |
|
| |
B. Distance from bottom of sink | ] | B | |
bowl to centerline of discharge | |||
outlet. (Add 1/2" when stainless |
|
| |
steel sink is used.) | A, |
| |
C: Distance from centerline of | L |
| |
the discharge outlet to end |
| ||
of discharge | tube. |
| |
D: D_sposer Width
D
E:Distance from disposer vertical centerline to centerline of
F:Centerline of disposer discharge to centerline at waste pipe entering wall. (Dimension "F" must be greater than 1/4" to prevent standing water in disposer.)
If replacing an | existing disposer, | skip ahead | to Instruction | 6. | ] |
If this is a first | time installation, | continue with | Instruction | 2. | / |
DISCONNECT SINK DRAIN
1.Loosen nut (A) at top of
2.Loosen nut (B) at top of extension pipe. Remove extension pipe.
3.Loosen nut (C) at base of sink flange. (If nut is corroded or too tight, apply penetrating lubricant
4.Push s_nk flange up through sink hole and remove it (see Figure
5.Clean sink flange area of any putty or other debris.
DISASSEMBLE NEW DISPOSER
MOUNTING ASSEMBLY
1.Insert wrenchette (or screwdriver) into one mounting lug and hold lower mount- ing ring securely with one hand (see Figure
2.Turn mounting assembly over (see Figure
screws (A) until you can access snap ring (B).
3Use screwdriver to pry snap ring off of sink flange. Mounting assembly will now come apart.
INSTALL FLANGE IN SINK HOLE
1.Roll 1/4 pound (4 oz.) of
2.Apply putty evenly around sink hole (see Figure
3.Press sink flange slowly but firmly into sink drain hole to seat evenly on putty
(see Figure
_k CAUTION
Do not use plumber's putty on any other disposer connection - it may harm disposer and cause property damage.
1odel |
| A | B | C |
| b | E |
010/6012 | 11 | 3/8" | 6" | 4" | 6 5/16" | 5" | |
01116013 | 12 | 5/8" | 6" | 4" | 6 5/16" | 5" | |
0552 | 12 | 5/8" | 6" | 4" | 7 1/4" | 5" | |
|
|
| |||||
_3/4" |
|
| 611/16" | 4'=._ 81/2'.=_=53/4'_ | |||
|
| 3/4" | 6 11/16" | 4" | 8 | 1/2" | 5 3/4" |
0559* _1157/8" | 9 7/16" | 4" | 7 | 1/2" | 5 3/4" | ||
| " | 6" | 4" | 7 | 1/4" | 5" | |
|
|
| 6" | 4" | 7 | 1/4" | 5" |
_'"Indicates Batch Feed Model
J
" | - r | " | /_ |
/!i
ATTACH UPPER MOUNTING ASSEMBLYTO SINK FLANGE
You may wish to place a we=ghted object in the sink to hold the sink flange in place. (Place a towel under object in sink to prevent scratching ) Reference F=gure
1 | Working from | under sink, slip fiber gasket and 4 Tighten three mounting screws up to sink | |||
| metal backup | ring over | sink flange. |
| until mounting assembly is seated tightly |
2 | Holding fiber | gasket and backup ring in place, | and evenly against sink. | ||
| shp mounhng | nng over | s_nk flange | so it seats | * Placing a thick, wide rubber band around |
| against backup nng |
|
| the sink flange (above the snap ring | |
3 | W_th fiber gasket, backup nng, and mounting | groove) may help hold parts Jnplace _,,hde | |||
| ring hght to S,F.'.ottom, | shde snap | r',ngcnto | tnstalhng snap ring. (Remember to rer'nove | |
| s_nk flange until _tpops | {nto groove | on flange'. | rubber band after snap ring is installed.) ' | |
If you are replacing an existing disposer, go to Instruction 6 If this is a first time _nstallahon, 1
skip ahead Io Instruction 7 | J |
Sink Flange
Fiber Gasket /
Backup R=ng __ _._'_).
MountEng RLng __
Snap Ring | O |