Kenmore 790.4380* Cooktop Control Pads, Using the Touch Control, Error Codes Display Message

Cooktop Control Pads

Using the Touch Control

Be sure that your finger is placed in the center of the touch pad. If the finger is not placed on the center of a pad, the cooktop may not respond to the selection made.

Lightly contact the pad with the fiat part of your entire

fingertip. Do not just use the narrow end of your fingertip.

Cooktop Power Pad

The Cooktop POWER key pad activates the entire Cooktop. To power the cooktop, touch and hold the POWER key pad for 2 seconds. A beep wiii sound and the Power LED will glow (Fig. 11). The cooktop wiii be in a ready mode for 10 seconds. If no other key pads are touched the Cooktop Main POWER will turn OFF automatically. To turn the Main Power OFF touch and hold the Main POWER key pad for 1 second. A beep wiii sound and the Power LED wiii turn OFF (Fig. 10).

Cooking Zone On/Off Pad

Each of the Cooking Zones have separate ON/OFF key pads. Once the Main Power key pad has been touched to activate the cooktop, touch the corresponding Cooking Zone ON/OFF key pad once to activate the Cooking Zone

needed. "-" will appear in the Alpha-Numeric display and the cooking zone ON/OFF LED will glow [Fig. 17). If the corresponding UP/DOWN Arrow key pad is not touched within 10 seconds, the request to turn the Cooking Zone ON will cancel and the Cooktop will go back to ready mode. To turn OFF a Cooking Zone, touch the Cooking Zone ON/OFF key pad once. The Cooking Zone LED will turn OFF {Fig. 16).

@

Fig. 16 Fig. 17

Fig. 10 Fig. 11

Controls Lock Pad

This feature allows the cooktop to be locked only when the cooktop is switched to OFF. Touch and hold the LOCI( key pad for 3 seconds. A beep will sound and the Loci< LED will glow (Fig. 13). Once locked, no other displays wiii glow and no Cooking Zones wiii activate. To turn the Controls Loci< OFF, touch and hold the LOCI( key pad for 3 seconds. A beep will sound, the Loci< LED wiii turn OFF (Fig. 12) and the

cooktop may be used normally. •

Fig. 12 Fig. 13

Error Codes Display Message

The error code will display in the zone that has the error. The error will flash through the code C, X, X (Example Fig. 14) where the X is the number of the code. If the zone has been on and the zone is hot enough to display H [Example Fig.

15)and you have an error then you will see C, X, X, H. For service call I=800=4=MY=HOME®.

Fig. 14

Fig. 15

Power Level Settings

The Cooking Zones have separate Power Level Alpha- Numeric displays. Once active, the Cooking Zones will provide 15 Power Levels to choose from. These include 1(Fig. 18), 2, 2, 3, 3., % LI.,S, 5., 6, E. (Fig. 19), 7, 8, 9, ,o. Half power levels [available between 2 and "/power level) are indicated by lighting the display decimal point (Fig. 19). The highest

setting of P or "Power Boost" provides approximately 139% power for 10 minutes (Fig. 20). After 10 minutes, the power level drops to 9. Each key pad touch (or just holding down the Power Level key pad) will scroll through all the available power levels for any Cooking Zone quickly.

Fig. 18 Fig. 19 Fig. 20

Residual Heat Message

Once any Cooking Zone has been used for cooking and turned OFF, and if the cooktop surface temperature on any of the Cooking Zones is still too HOT, H (Fig. 21) will appear

in the Alpha-Numeric display for the affected Cooking

Zone. The H will continue to display if the temperature is still too HOT.

The Cooking	Zones	may
appear to be cool while turned ON and after
they have been turned OFF. But the glass
surface may be HOT from residual		heat
transferred from the cookware	and	burns may	Fig. 21
occur if surface is touched.

8