Install Filtered Water Faucet | Kenmore 625.38501 specification

Step 2 - Install Filtered Water Faucet

MAKE HOLE FOR FAUCET

IMPORTANT: A 1-1/4” dia. hole is needed to mount the filtered water faucet. To avoid damaging the sink, con- sult a qualified plumber or installer for drilling proce- dures in porcelain or stainless steel.

1.Select one of the following options to install the faucet. Make sure there is room underneath to make the need- ed connections.

Use an existing sink top hole for spray hose or soap dispenser (must be 1-1/4” in diameter).

Drill a new hole in the sink top.

Drill a hole in the countertop next to the sink.

2.Check to make sure the filtered water faucet base will sit flat against the mounting surface.

3.If drilling is needed, make a 1-1/4” dia. (minimum) hole for the faucet in the mounting surface.

INSTALL FAUCET BASE

1.Locate the faucet base (See Fig. 5) and feed the toggle bolts down through the hole until the faucet base is square against the mounting surface (sink or counter- top). The rubber gasket should be between the faucet base and mounting surface.

2.Tighten the toggle bolts until the faucet base is firmly mounted to the surface. Do not overtighten.

CONNECT BLUE TUBE TO FAUCET

1.Place the Advanced Two-Stage Drinking Water Filter housing under the sink. It can sit upright or on its side.

2.Locate the blue tube. One end is attached to the filter housing. Feed the other end up through the mounting hole and faucet base. See Figure 6.

3.Refer to the “Cut Tubes to Length” section on Page 8 and cut the blue tube square and to length as needed, leaving about 6 inches above the faucet base.

4.Locate the faucet. Refer to the “Connect Tubes” section on Page 8 and insert the blue tube all the way into the 3/8” quick connect fitting on the faucet bottom.

5.Pull on the tube to be sure it is held firmly in the fit- ting.

INSTALL FAUCET ON BASE

1.Lower the faucet onto the base. See Figure 7.

2.Give the faucet a 1/4 turn clockwise to attach the faucet to the base.

3.Install battery in faucet base (See “Change Battery” sec- tion on Page 9) then continue installation with Step 3 on Page 8.

faucet base		1-1/4” dia. hole

rubber gasket

		through sink or

toggle bolts		countertop

Figure 5

faucet

faucet base

blue tubing

filter housing

Figure 6

faucet

1/4 turn to connect faucet to base

faucet base

Figure 7

Questions? Call The Kenmore Water Line 1-800-426-9345 or visit KenmoreWater.com

625.38501 specifications

The Kenmore 625.38501 is a robust water softener designed to enhance the quality of water in residential settings. Known for its reliability and efficiency, this model features a slew of advanced technologies that tackle hard water problems while maximizing the user experience.

One of the standout characteristics of the Kenmore 625.38501 is its capacity to eliminate hard water minerals such as calcium and magnesium. By doing so, it helps prevent scale buildup in pipes and appliances, ultimately prolonging their lifespan. This softener has an exceptional flow rate, making it suitable for homes of varying sizes, from small households to larger families with varying water needs.

A notable technology featured in the Kenmore 625.38501 is its smart regeneration system. This innovative feature automatically adjusts the regeneration cycle based on the water usage of the household. By monitoring consumption patterns, the system minimizes salt and water usage during regeneration, making it not only economical but also eco-friendly.

The user-friendly digital display is another highlight of this water softener. It allows residents to easily monitor water usage and remaining salt levels, simplifying maintenance. Additionally, the softener is equipped with a built-in salt indicator that alerts users when it’s time to refill salt, ensuring optimal performance at all times.

Installation of the Kenmore 625.38501 is straightforward, thanks to its compact design and clear instructions. It can be integrated seamlessly with existing plumbing systems, and its user-friendly interface means that homeowners can operate and manage the softening process without requiring extensive technical knowledge.

Moreover, Kenmore is renowned for its commitment to durability and quality. The 625.38501 is constructed from high-quality materials that are designed to withstand the rigors of daily use. This ensures longevity and provides peace of mind to users, knowing that they have made a worthwhile investment in their home's water quality.

In summary, the Kenmore 625.38501 water softener stands out for its advanced technology, smart regeneration system, and user-centric design. It represents an ideal solution for homeowners looking to improve their water quality, protect their plumbing system, and enhance the overall comfort of their living environment. With its efficiency and reliability, this water softener continues to be a favorite among consumers.