Avaya 10-Watt manual Installation, Wiring Connections, Mounting, Input Wiring

Page 5

Installation

Mounting

Wall Mounting

The amplifier is designed for wall mount applications. The 10-watt amplifier weighs 4 lb.

NOTE: The amplifier will produce heat during operation which will rise and may cause problems for temperature-sensitive equipment mounted above it. Mount the amplifier near the top of the backboard so that no other equipment will be above it. If this is not possible, then allow at least 12" between the top of the amplifier and the bottom of any equipment positioned above it. Also allow at least 4" between the bottom of the amplifier and any equipment below it to allow for adequate air circulation. In addition, because the unit itself gets hot, avoid touching it during operation.

To wall mount this unit, use the two 5/8” pan head screws with nylon washers provided.The screws should protrude approximately ¼" from the surface of the backboard. Lift the amplifier and place it over the two screws using the keyhole slots in the flanges at the sides of the amplifier.The screws should engage the keyhole slots. Once in the keyhole slots, tighten the screws to secure the amplifier.

Wiring Connections

 

IMPORTANT: Before making any connections or wiring changes to the amplifier

 

or any equipment connected to the amplifier, make sure that the amplifier is NOT

 

plugged into an AC outlet.

 

NOTE: The amplifier does not have a power switch, so it must be unplugged in

 

order to turn the power off.

Input Wiring

All signal input and control wiring is made to the terminal strip on the front of the

 

unit.

TEL Input and Control Pair

The telephone input is a 600-ohm, dry loop, balanced input available at the T and R

 

terminals. It is controlled by a dry contact closure that is made between the control

 

terminals labeled TEL CONT and GND. Shorting these terminals together will mute

 

the background music input and open the Tel page channel (see Figure 2).

 

NOTE: In instances where the amplifier is to be placed permanently in the Tel page

 

mode, a wire jumper must be installed between the TEL CONT and GND terminals.

Page 5 of 8

Image 5
Contents Telephone Paging Amplifier 10-Watt Model Domestic and International Approvals Important Safety InformationSupport Information Contents Introduction Package ContentsTelephone Paging Amplifier Wiring Connections InstallationInput Wiring MountingWiring for TEL Input Speaker Connection Output WiringControls IndicatorOperation

10-Watt specifications

Avaya 10-Watt is a powerful and innovative feature-rich device designed for modern communication systems, specifically catering to businesses looking for efficiency and reliability in their telephony solutions. This device is integral to Avaya's extensive line-up, utilized in various networking applications, especially within VoIP environments.

One of the standout features of Avaya 10-Watt is its Power over Ethernet (PoE) capability. This functionality enhances installation flexibility, allowing the device to receive power through the data cable itself, minimizing the need for additional power sources. This enables easier deployment in diverse working environments and reduces clutter from extra cables.

The Avaya 10-Watt is designed with advanced sound quality technology, including wideband audio support that delivers crystal-clear voice communications. The incorporation of high-definition audio ensures that every conversation is more intelligible and lifelike, thus improving user experience significantly.

Moreover, the device features robust security protocols, ensuring that conversations and data are protected against unauthorized access. The strong encryption measures included in the device's communication protocols provide peace of mind to businesses that prioritize confidentiality and data integrity.

Another defining characteristic of the Avaya 10-Watt is its user-friendly interface. With programmable keys and backlit displays, users can easily navigate through features and settings, promoting efficient and effective communication. The device can accommodate multiple lines and extension capabilities, making it suitable for dynamic business operations.

In terms of interoperability, the Avaya 10-Watt seamlessly integrates with various Avaya communication platforms, as well as third-party applications. This flexibility allows organizations to optimize their existing infrastructures while reducing long-term costs associated with new installations.

Additionally, the Avaya 10-Watt supports advanced features such as call forwarding, voicemail, and conferencing. These capabilities enhance teamwork and collaboration within organizations, allowing employees to communicate more effectively regardless of their location.

Overall, Avaya 10-Watt is a reliable choice for businesses seeking modern telephony solutions that combine flexibility, security, and user-centric features. Its advanced capabilities ensure that it effectively meets the diverse communication needs of organizations, paving the way for improved productivity and collaboration.