Murray 425620x92A manual Operating Tips, Mowing and Bagging Tips

Page 20

OPERATION

OPERATING TIPS

1.Check the blade rotation control for correct adjustment. For the blade(s) to disengage correctly, the adjustment must be cor- rect.

2.Before you use the unit, check the oil in the engine and add oil if necessary.

3.If the engine will not start, first make sure the wire is attached to the spark plug.

4.Make sure all the belts are inside all the belt guides. See the in- structions on how to remove and install the motion drive and mower drive belts.

5.Before you make an inspection, adjustment (except for the car- buretor) or repair, make sure the wire from the spark plug is dis- connected.

6.For longer life of the battery on electric start models, charge the battery every three months.

7.Use the speed control pedal to change the ground speed, not the throttle control.

8.Belt noise can occur when the blade is engaged. This noise is normal and does not affect the operation of the unit.

MOWING AND BAGGING TIPS

1.For a lawn to look better, check the cutting level of the mower housing. See “How To Level The Mower Housing” in the Main- tenance section.

2.For the mower housing to cut level, make sure the tires have the correct amount of air pressure.

3.Every time you use the unit, check the blade. If the blade is bent or damaged, immediately replace the blade. Also, make sure the nut for the blade is tight.

4.Keep the blade(s) sharpened. Worn blades will cause the ends of the grass to turn brown.

5.Do not cut or bag grass that is wet. Wet grass will not discharge correctly. Let the grass dry before cutting.

6.Use the left side of the mower housing to trim near an object.

7.Discharge the cut grass onto the mowed area. The result is a more even discharge of cut grass.

8.When you mow large areas, start by turning to the right so that the cut grass will discharge away from shrubs, fences, drive- ways, etc. After one or two rounds, mow in the opposite direc- tion making left turns until finished (Figure 11).

9.If the grass is very high, cut two times to decrease the load on the engine. First cut with the mower housing in the highest posi- tion and then lower the mower housing for the second cut.

10.For better engine performance and an even discharge of the cut grass, always operate the engine with the throttle in FAST position.

11.When you use a bagger, operate the engine with the throttle in FAST position and the speed control pedal pushed 1/3 forward.

12.For better cutting performance and a quality cut, mow with the speed control pedal pushed 1/3 to 1/2 forward.

13.After each use, clean the bottom and top of the mower housing for better performance. Also, a clean mower housing will help prevent a fire.

Figure 11

F–040729L

20

Image 20
Contents Model Table of Contents OWNER’S Information Environmental AwarenessII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Steps to Follow Before MowingSafety Warning Pictorials International PictorialsInternational Pictorials Control And Operating PictorialsAssembly AssemblyHOW to Assemble the Gauge Wheels HOW to Install the SeatHOW to Assemble the Steering Wheel HOW to Install the Battery Cables Maintenance Free BatteryHOW to Charge Maintenance Free Battery HOW to Prepare the Engine Check the Level of the Mower HousingIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsHOW to USE the Throttle Control AttachmentsHOW to USE the Speed Control Pedal HOW to Disconnect the TransmissionHOW to SET the Parking Brake HOW to Change the Cutting HeightHOW to Stop the Unit HOW to Transport the UnitHOW to Operate with the Mower Housing HOW to Operate the Unit on HillsCarburetor HOW to Start the EngineBefore Starting the Engine Operating Tips Mowing and Bagging TipsMaintenance Frequency Maintenance Required CommentsHOW to Check the Muffler General RecommendationsInspect Blade HOW to Remove and Install the BladeHOW to Sharpen the Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Motion Drive Belt Remove the 1/4 inch 6 mm pin or bolt FigureHOW to Check and Adjust the Drive Brake Where to Lubricate HOW to Check the Fuel FilterHOW to Remove the Mower Housing HOW to Install the Mower HousingHOW to Adjust the Gauge Wheels HOW to Level the Mower Housing HOW to Replace the Motion Drive Belt RemovalHOW to Replace the Mower Drive Belt HOW to Install the Wheels Front WheelHOW to Replace the Fuse HOW to Replace the Light BulbHOW to Clean the Mower Housing BatteryTrouble Shooting Chart 040729L USARepair Parts Chassis & HoodKey Description Repair Parts Drive Assembly Drive Assembly Steering Key Part Description Repair Parts Mower Housing Suspension Mower Housing Suspension Mower Housing Complete Mower Housing Assy Repair Parts Engine Mount Engine Mount Electrical System Light HarnessElectrical System 040729L Index Model No Model No Bushel Capacity