Murray 405000x8B manual Trouble Shooting Chart, Problem The engine will not start

Page 33

TROUBLE SHOOTING CHART

PROBLEM: The engine will not start.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric–Start Models: Clean the battery terminals. Tighten the cables.

3.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

4.Remove the spark plug(s). Move the throttle to the SLOW posi- tion. Turn the ignition key to the ON position. Try to start the en- gine several times. Install the spark plug.

5.Replace the spark plug.

6.Adjust the carburetor.

PROBLEM: The engine will not turn over.

1.Follow the steps, “How To Start The Engine” in this book.

2.Electric–Start Models: Check the level of the acid in the battery. If needed, add water. Charge the battery.

3.Replace the fuse.

4.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

5.Electric–Start Models: replace the solenoid. Recoil–Start Mod-

els: replace the module.

PROBLEM: The engine is difficult to start.

1.Adjust the carburetor.

2.Replace the spark plug.

3.Replace the fuel filter.

PROBLEM: The engine does not run smooth or has a loss of power.

1.Check the oil.

2.Clean the air filter.

3.Clean the air screen.

4.Replace the spark plug.

5.The engine is working too hard. Use a lower gear.

6.Adjust the carburetor.

7.Replace the fuel filter.

PROBLEM: The engine does not run smooth at fast speed.

1.Replace the spark plug.

2.Adjust the throttle control.

3.Clean the air filter.

4.Replace the fuel filter.

PROBLEM: The engine stops when the blades are engaged.

1.To activate the seat sensor, always sit in the middle of the seat.

2.Check the wiring harness for damage or a loose connection. Repair the damaged wire.

PROBLEM: On slopes, the engine stops.

1.Mow up and down slopes. Never mow across a slope.

2.To activate the seat sensor, always sit in the middle of the seat.

PROBLEM: The engine will not idle.

1.Replace the spark plug.

2.Clean the air filter.

3.Adjust the carburetor.

4.Adjust the throttle control.

5.Drain the fuel tank. Clean the fuel line. Replace the fuel filter.

PROBLEM: A hot engine causes a decrease in power.

1.Clean the air screen.

2.Check the oil.

3.Adjust the carburetor.

4.Replace the fuel filter.

PROBLEM: Excessive vibration.

1.Replace the blade.

2.Check for loose engine bolts.

3.Decrease the air pressure in the tires.

4.Adjust the carburetor.

5.Check for a damaged belt or damaged pulley. Replace the damaged parts.

PROBLEM: The grass does not discharge correctly.

1.Stop the engine. Clean the mower housing.

2.Raise the height of cut.

3.Replace or sharpen the blade(s).

4.Move the shift lever to a slower speed.

5.Move the throttle control to the FAST position.

6.Replace the spring for the blade idler.

PROBLEM: The mower housing does not cut level.

1.Check the air pressure in the tires.

2.Adjust the level of the mower housing.

3.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

PROBLEM: The mower blades will not rotate.

1.Check the mower drive belt. Make sure the belt is installed cor- rectly.

2.Replace the mower drive belt.

PROBLEM: The unit will not move when the clutch is engaged.

1.Check the motion drive belt. Make sure the belt is installed correctly.

2.Adjust the clutch.

3.Replace the motion drive belt.

PROBLEM: The unit moves slower or stops when the clutch is engaged.

1.Adjust the clutch.

2.Replace the motion drive belt.

PROBLEM: When the clutch/brake pedal is released, belt noise can be heard.

1.Temporary belt noise does not change the operation of the unit. If belt noise is continuous, check the routing of the belt. Make sure the belt is inside all belt guides.

2.If the noise is continuous, adjust the clutch.

PROBLEM: The rear wheels spin over uneven terrain.

1.Check the front axle. If the front axle does not freely pivot, loos- en the axle bolt(s).

PROBLEM: The transaxle is difficult to shift between gears with the engine running and the clutch depressed.

1.Check the clutch adjustment to make sure the belt stops when the clutch pedal is depressed with the transaxle in (N) neutral.

2.Check the belt guides around the transaxle drive pulley. Make sure the belt guides do not touch the pulley.

F–030745L

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Model Table of Contents Responsibility of the Owner OWNER’S InformationII. Slope operation Safe Mowing Guide Safe Mowing Guide Safe Mowing Guide Before Mowing Steps to FollowInternational Pictorials International PictorialsAssembly AssemblyHOW to Assemble the Steering Wheel HOW to Install the SeatMaintenance Free Battery HOW to Charge Maintenance Free BatteryHOW to Install the Battery Cables Check the Level of the Mower Housing HOW to Prepare the EngineIMPORTANT! Before YOU Start Mowing Check the TiresOperation Location of ControlsLift Lever HOW to USE the Throttle Control HOW to USE the Shift LeverAttachments HOW to Change the Cutting Height HOW to SET the Parking BrakeHOW to Stop the Unit HOW to Transport the UnitHOW to Operate the Unit on Hills HOW to Operate with the Mower HousingHOW to Start the Engine Before Starting the EngineCarburetor Mowing and Bagging Tips Operating TipsMaintenance Chart MaintenanceHOW to Check the Muffler General RecommendationsHOW to Remove and Install the Blade HOW to Sharpen the BladeInspect Blade HOW to Adjust the Blade Rotation Control HOW to Check and Adjust the Drive Brake HOW to Check and Adjust the ClutchDisconnect the adjuster nut from the shifter bracket Figure HOW to Adjust the Shift LeverHOW to Check the Fuel Filter Where to LubricateHOW to Install the Mower Housing HOW to Remove the Mower HousingHOW to Level the Mower Housing Removal HOW to Replace Motion Drive BeltInstallation HOW to Replace the Mower Drive Belt Front Wheel HOW to Install the WheelsHOW to Replace the Light Bulb HOW to Replace the FuseHOW to Clean the Mower Housing BatteryProblem The engine will not start Trouble Shooting ChartMURRAY, INC. Lawn Mower Central Parts Distributors 030745L Chassis & Hood Repair PartsKey Description Motion Drive Motion Drive Steering Steering Mower Housing Suspension Repair Parts Repair Parts Mower Housing 7601044 Repair Parts Engine Mount Engine Mount Repair Parts Electrical System Electrical System 030745L Index Lawn Tractor Accessories

405000x8B specifications

The Murray 405000x8B is a robust, high-performance piece of equipment designed for industrial applications that require precise engineering and unparalleled efficiency. Known for its reliability and innovative features, the 405000x8B is a standout in the world of advanced machinery.

One of the main characteristics of the Murray 405000x8B is its powerful engine, which delivers exceptional output while maintaining energy efficiency. This system incorporates advanced fuel injection technology that optimizes combustion, ensuring less fuel consumption without sacrificing performance. This not only makes the equipment environmentally friendly but also reduces operating costs significantly.

In terms of design, the 405000x8B boasts a compact yet sturdy construction that allows it to operate effectively in a variety of environments. Its lightweight framework enhances maneuverability while maintaining durability, enabling it to adapt to both on-site and off-site applications. Additionally, the unit is equipped with an advanced cooling system that prevents overheating, ensuring optimal performance even in demanding conditions.

The Murray 405000x8B also features cutting-edge automation technologies that enhance usability and control. Users can take advantage of an intuitive interface that simplifies operation and monitoring. This includes real-time data displays that provide insights into performance metrics, allowing for proactive maintenance and reducing downtime.

One of the hallmark technologies of the 405000x8B is its integration with IoT (Internet of Things) capabilities. This feature enables remote monitoring and telemetry, allowing operators to track performance and receive alerts for any anomalies. Such connectivity enhances operational efficiency and facilitates timely maintenance actions.

Moreover, the unit is designed with safety in mind. It includes a host of integrated safety features, such as automatic shutoff mechanisms and emergency backup systems, ensuring the protection of operators and the equipment itself.

In summary, the Murray 405000x8B is a versatile and efficient piece of industrial machinery that combines powerful performance with innovative technologies. Its robust design, intelligent automation capabilities, and safety features make it an ideal choice for a wide range of applications, solidifying its reputation as a leader in the industry. Whether used in manufacturing, construction, or other sectors, the 405000x8B is engineered to deliver results that businesses can rely on.
Top Page Image Contents