Siemens 500 service manual Ranges, 4 UP0/E Interface, USB 1.1 Interface

Page 35

Product Description

Technical Data

2.6.3Ranges

The transmission range with a 0.6 mm PVC cable is at least 1,000 meters (100 meters from primary to client device).

The feeding range can be checked via the optiPoint menu item "Service", "Line Test". This test activates all LEDs for 3 or 5 seconds (depending on the system type), turns on the ringer for 1 second, and blanks the display.

Detailed range data for the individual cable types can be found in the ICN TI Hicom 150 E/ Hi- com 300 E and in the ICCS Manual, Volume 2 (order no.: A30951-V6200-*-7620/Lieferzentrum Fürth).

2.6.4UP0/E Interface

The UP0/E interface is a vendor-specific ISDN interface that uses the CorNet TS protocol and a powered two-wire interface for connecting the optiPoint500 telephones.

UP0/E interface

Data transmission based on time-division multiplexing with AMI codes

250 µs frame

 

 

 

Bit clock

 

384 kHz

 

 

 

Net bit rate

 

144 kbps

 

 

Aggregate bit rate

152 kbps

 

 

Center frequency

192 kHz

 

 

Characteristic impedance at 192 kHz

100 ohms

 

 

 

Table 2-8

UP0/E interfaces: technical data

 

2.6.5USB 1.1 Interface

optiPoint 500 telephones are upgraded with a USB interface (with the exception of optiPoint 500 entry). This is the basis for:

●PC-supported telephony (TAPI)

CallBridge TU and CallBridge for data are TAPI Service Providers for CTI solutions. Telephones can communicate with the PC using these.

●Data transmission via the PC’s USB interface using CAPI (e.g. direct Internet access, fax transmission, e-mail, etc.). When the CAPI software is installed, PCs gain direct access to the Internet via the USB interface, without requiring an additional adapter. This software is subject to charges.

TAPI and CAPI can be used in parallel (e.g. you can receive a large e-mail or download data, etc. while setting up calls via a CTI application).

P31003-E8400-A100-3-7620

2-21

Service Manual

Page 34 Page 36
Image 35
Page 34 Page 36
Contents P31003-E8400-A100-3-7620 1PP31003-E8400-A100-3-7620 Contents Ordering Information TroubleshootingP31003-E8400-A100-3-7620 P31003-E8400-A100-3-7620 Figures P31003-E8400-A100-3-7620 Tables P31003-E8400-A100-3-7620 Safety Information General Service InformationService Concept Guidelines for Members of Siemens Staff Safety SymbolsGuidelines for Using Data General Service Information Product Description Product DescriptionAdditional Features when Connecting optiPoint 500 to HiPath OptiPoint 500 Features at Hicom/HiPathFeatures when Connecting to Hicom and HiPath Modules Add-On Components and Adapters Configuration NotesControls Connectivity Telephones OptiPoint 500 entryOptiPoint 500 economy OptiPoint 500 basic OptiPoint 500 standard Controls Special FeaturesOptiPoint 500 advance Module Options Configuration NotesOptiPoint 500 key module Busy Lamp Field BLF Power SupplyProduct Description Connection to the Terminal Interface Description MW8/8 RJ45 I2C Bus Memory Cards OptiPoint 500 signature module HiPath 4000 onlyOptiset E External Speaker Accessories External Speaker/Desk MicrophoneDesk Microphone Headset Order Number Connect to OptiPoint HeadsetsConnecting the Headset to an 121TR9-5 Interface Pin Assignment Local Power Supply UnitPrimary/Client Configuration see .5 on Name ValueWall Mounting Accessory PackOnline Key Labeling Tool Environmental Conditions Technical Data Asset IDAmbient temperature Relative humidity USB 1.1 Interface Ranges4 UP0/E Interface Product Description Keypad and Control Panel Setting Up the TelephoneStartup Unpacking the BoxPressing the Plus/Minus Key Simultaneously Date and Time IndicatorKeypad Polling USB Ports on the Underside of the TelephoneCode Menu text Action after pressing OK Number Accessing the Telephone TestTelephone Tests OptiPoint 500 telephone Test Function Not WorkingHiPath 4000/Hicom 300H HiPath 3000/Hicom 150 HStartup OptiPoint 500 entry, economy block diagram Block DiagramsOptiPoint 500 basic, standard and advance block diagram Private Network Termination Units Private Network Termination UnitsDistance Adapter Ucon S and M at Hicom 300/300 E and HiPath PNT Private Network TerminationPNT E Private Network Termination PNT Q Private Network TerminationOption Adapters and Ports Option Adapters and PortsOption Adapters and Ports Configuration Notes Adapter Slots You can connect the following to this adapter OptiPoint 500 acoustic adapterFloating contact MW6/6 Headset MW8/8 Cable MW8/8Electrical Requirements of the Headset Contact Load Floating ContactsRJ11 Functions OptiPoint 500 Analog AdaptersAdapter does not support the following functions Analog InterfaceRJ45 OptiPoint 500 Isdn AdapterRestriction OptiPoint 500 Phone Adapter Host/ClientRJ11 Functional DescriptionSecond Handset MW 4/4 Pin OptiPoint 500 recorder adapterInterfaces Interface DescriptionElectrical Requirements Host Connection ExampleClient USB Port OverviewBLF CallBridge CallBridgeCallBridge TU CallBridge for Data IP Adapter IP Adapter AdministrationIP Adapter System connection of optiPoint IPadapter OptiPoint IPadapter InstallationConnection to the Terminal PIN assignments on the IPadapter Connection to the SystemHicom OptiPoint IPadapterStructural overview Administration Via the Web BrowserError example Fault signalingOptiPoint IPadapter Tel OptiPoint IPadapter Home General information AdministrationAdministrator settings IP address and routing CorNet TC parameters Speech parameters Click File transfer and enter all appropriate parameters FTP parameter DefaultIP Adapter Load download from fileserver application Save upload to fileserver configuration Load download from fileserver configurationHistory file Restart terminal Invoke tests DiagnosticsChange administrator password Administration via optiPoint No Dhcp response Press any key? Error codes for configuration settings Start phone? Enter the appropriate password for Secured menu DHCP? Example Dhcp Input Example OIP IP address Exit Example Mode InputConfiguration Examples WEB access to the IPadapter WEB page administration IP address and routing Configuration in HG 1500 and Office 11 optiPoint IPadapter homepage 12 WEB page administration 13 IP address and routing Configuring the optiPoint IPadapter on the optiset E IP Adapter Test Loops TroubleshootingReboot Test Loops 3Reboot Name Color Part Number Ordering InformationOrdering Information Accessories, Spare Parts, Miscellaneous Extra Headset Ordering Information Name Reference number DocumentationProduct Company Address Telephone Order Fax Form Re Cipient Order AddressesProduct Company Address Telephone Order form Fax Recipient After-Sales Service and RepairSubject Address Intranet AddressesOrdering Information Abbreviation Definition AbbreviationsIsdn Index P31003-E8400-A100-3-7620
Related manuals
Manual 36 pages 28.92 Kb Manual 27 pages 28.17 Kb Manual 36 pages 59.75 Kb Manual 106 pages 25.08 Kb

500 specifications

Siemens has been at the forefront of innovation in industrial automation and control systems, and the Siemens 500 and 700 series PLCs (Programmable Logic Controllers) exemplify this commitment to technology and efficiency. Both series are designed to meet the diverse needs of modern manufacturing and process automation, integrating robust features and advanced technologies to enhance operational performance.

The Siemens S7-500 series is known for its high performance and scalability. It is equipped with a modular architecture, allowing for the easy expansion of I/O modules according to project requirements. The S7-500’s processor options range from basic to high-end solutions, enabling users to select the appropriate level of control for their applications. The series supports a comprehensive range of programming languages, including Ladder Logic, Function Block Diagram, and Structured Text, aligning with the diverse backgrounds of automation engineers.

One of the standout technologies in the S7-500 series is the use of the Industrial Ethernet network, known as PROFINET, which ensures rapid data transfer and seamless connectivity. This capability is vital for real-time monitoring and control of industrial processes. Additionally, the S7-500 supports various communication protocols that can be integrated into complex networked environments, enhancing interoperability with other devices and systems.

On the other hand, the Siemens S7-700 series offers a step further in flexibility and performance, particularly designed for complex automation tasks. The S7-700 controllers leverage powerful processors and advanced memory capacity, which are essential for tackling high-speed and resource-intensive applications. The series also features integrated diagnostics and troubleshooting tools that facilitate easier maintenance and reduce downtime in manufacturing operations.

The S7-700 series further incorporates features such as integrated safety functionality through the Safety Integrated technology, providing a comprehensive solution for applications requiring both automation and safety controls. Additionally, its modular design allows for a wide range of options for I/O and communication modules, making it highly adaptive to various industry requirements.

In conclusion, Siemens 500 and 700 series PLCs are notable for their advanced technologies, versatility, and robustness. With their modular designs, comprehensive programming capabilities, and support for modern communication protocols, they play a critical role in optimizing industrial automation processes, helping companies achieve higher productivity and efficiency. As industries continue to evolve, Siemens remains committed to providing cutting-edge solutions that empower businesses to thrive in a competitive landscape.
Top Page Image Contents