Electrolux AG17542STA manual To Adjust Steering Wheel ALIGN- Ment, Front Wheel TOE-IN/CAMBER

Page 24

Engine

Pulley

Clutching

Idler

Stationary

Idler

Center

Span

Keeper

Transaxle

Pulley

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not

horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retaining

Ring

Axle

Cover

Square Key

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BAT- TERY" in the MAINTENANCE section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure: IMPORTANT: Your tractor is equipped with a 12 volt system. The other vehicle must also be a 12 volt system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

1.Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

2.Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

3.Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

1.BLACK cable first from chassis and then from the fully charged battery.

2.RED cable last from both batteries.

Weak or Dead

Fully Charged

Battery

Battery

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model NO. AG17542STA Table of Contents WarrantySafety Rules General OperationII. Slope Operation IV. Service III. ChildrenDo not Safety Rules Product Specifications Customer ResponsibilitiesAPI-SG-SL Unassembled Parts Tools Required for Assembly HOW to SET UP Your TractorTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery Check Tire Pressure Check for Proper Position of ALL BeltsCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower To Operate on HillsTo Transport Before Starting the Engine To Start EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips Maintenance General Recommendations Lubrication ChartBefore Each USE Tractor Clean AIR Screen EngineTransaxle Cooling BeltsCleaning AIR FilterMuffler Spark PlugsService and Adjustments To Install MowerTo Remove Mower To Level Mower Housing SIDE-TO-SIDE AdjustmentTo Check and Adjust Brake To Replace Mower Blade Drive BeltTo Replace Motion Drive Belt To Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak BatteryFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Adjust Carburetor Battery OtherFuel System Engine OILTroubleshooting Chart Problem Cause CorrectionExcessive Poor grass Service Notes Suggested Guide for Sighting Slopes for Safe Operation
Top Page Image Contents