Craftsman 917.273134 owner manual Engine, To Adjustthrottle Control Cable, To Adjust Carburetor

Page 26

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an

authorized engine manufacturer's service outlet.

TO ADJUSTTHROTTLE CONTROL

CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever from slow to choke posi-

tion. Slowly move lever from choke to fast position.

2.Check to see if hole in throttle lever and hole in speed control bracket are aligned.

3.If holes are not aligned, loosen cable clamp screw and align the holes by inserting a pencil or a 1/4" drill bit through both holes.

4.Pull throttle cable up to remove slack and tighten cable clamp screw. Re-

move alignment pencil or drill bit.

TO ADJUST CARBURETOR

The carburetor has been preset at the

factory and adjustment should not be nec- essary. However, minor adjustment may

be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, proceed as follows:

In general, turning the adjusting needles in (clockwise) decreases the supply of fuel to the engine giving a leaner fuel/air mixture.

Turning the adjusting needles out (counter- clockwise) increases the supply of fuel to the engine giving a richer fuel/air mixture. IMPORTANT: Damage to the needles and seats in carburetor may result if turned in too tight.

NOTE: The carburetor on this engine is low emission. It is equipped with an idle fuel adjusting needle with a limiter cap, which allows some adjustment within the limits allowed by the cap. Do not attempt to remove the limiter cap. The limiter cap cannot be removed without breaking the adjusting needle.

1.Be sure you have a clean air filter and the throttle control cable is adjusted properly (see above).

2.Start engine and allow to warm for five minutes. Make adjustments with engine running and shift/motion control lever in neutral (N) position.

3.Idle speed setting - With throttle control lever in slow position, engine should

idle at 1750 RPM If engine idles too slow or fast, turn idle speed adjusting screw in or out until correct idle is at- tained.

4.Idle fuel needle setting - With throttle control lever in slow position, turn idle fuel adjustment needle in (clockwise) until engine begins to die and then turn out (counterclockwise) until engine runs rough. Turn needle to a point midway between those two positions.

5.Recheck idle speed. Readjust if nec- essary.

ACCELERATION TEST -

6. Move throttle control lever from slow to fast position. If engine hesitates or dies, turn idle fuel adjusting needle out (counterclockwise) 1/8 turn. Repeat test and continue to adjust, if neces- sary, until engine accelerates smoothly.

High speed stop is factory adjusted. Do not adjust - damage may result. IMPORTANT: Never tamper with the engine governor, which is factory set for proper engine speed. Overspeed- ing the engine above the factory high speed setting can be dangerous. If you think the engine-governed high speed needs adjusting, contact a Sears or other

qualified service center, which has proper equipment and experience to make any

necessary adjustments.

ver

Idle Speed

Adjusting'__T_-I

screwII ,d,eFoe,II

Adjusting--IT = =- f j I

Needle I''_JJ'!J

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents InFTSMnN Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation II. Slope OperationIV. Service Do notAPI-SF-SJ SAE Product SpecificationsSAE U1RRepair Protection Agreements Sears Installation ServiceCustomer Responsibilities Seat Howto SET UP Your Tractor Check Battery Check Brake System Install Mulcher PlateCheck for Proper Position ALL Belts Checklis TH L I,I Know Your Tractor LeverTo SET Parking Brake HOW to USE Your TractorTo Adjust Mower Cutting Height To USE Throttle ControlTo Operate On Hills To Adjust Gauge WheelsTo Operate Mower Towing Carts and Other Attach MentsADD Gasoline Before Starting the Engine Check Engine OIL LevelTo Start Engine Mowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartMaintenance Schedule Before Each USEBlade Removal TractorOperator Presence System To Sharpen BladeTransaxle Cooling BatteryEngine LubricationEngine OIL Filter To Service PRE-CLEANERCleaning Spark PlugsTo Install Mower Tractor To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Check and Adjust Brake To Replace Motion Drive BeltFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEU TraladjustmentTo Adjust Steering Wheel Align Ment To Start Engine with a Weak BAT- TeryReplacing Battery To Remove Hood and Grill AS- SemblyEngine To Adjustthrottle Control CableTo Adjust Carburetor Acceleration TestEngine OIL BatteryFuel System CylindersCause Correction Troubleshooting ChartProblem Loss of power CauseCorrection ProblemCause Tractor - Model Number 917,273134 Schematic Ignition SwitchTractor - Model Number 917,273134 Electrical KEY Part Description Tractor - Model Number 917,273134 Chassis and Enclosures KEY Part NO. NO. Description Tractor - Model Number 917,273134 Ground Drive KEY Part Tractor - Model Number 917,273134 Steering Assembly KEY Part NO. NO.DESCRIPTION Tractor - Model Number 917,273134 Engine Optional EquipmentTank, Fuel Tractor - Model Number 917,273134 Seat Assembly Tractor - Model Number 917,273134 Decals Wheels & TiresTractor - Model Number 917,273134 Lift Assembly KEY Part NO. NO.DESCRIPTION Tractor - Model Number 917,273134 Mower Deck Tractor - Model Number 917,273134 Mowerdeck 42A KEY Part Description Crankcase Cylinder HEAD/VALVE/BREATHER KEY Part Description Crankcase KEY Part NO. NO.DESCRIPTIONIGNITION/ELECTRICAL t Ealluiviagelectriqu E Blower Housing & Baffles Not IllustratedMoteur Starting System KEY Part Description OIL PAN/LUBRICATION Enginecontrols KEY Part Description=UELDELESYSTEME Exhaust KEY Part Description Fuelsystem KEY Part NO. noCrankshaft KEY Part Description Page Suggested Guide for Sighting Slopes for Safe Operation Your Home

917.273134 specifications

The Craftsman 917.273134 is a remarkable lawn tractor that stands out in the realm of outdoor power equipment. Designed for homeowners seeking a reliable and efficient solution for maintaining their lawns, this tractor combines performance and user-friendly features, making lawn care tasks simpler and more enjoyable.

One of the key attributes of the Craftsman 917.273134 is its powerful engine. Equipped with a robust 19 horsepower Briggs & Stratton engine, this lawn tractor delivers dependable performance and is capable of handling challenging terrains and heavier workloads. The engine is designed for easy starting and efficient fuel consumption, allowing users to complete their mowing tasks without frequent refueling interruptions.

The cutting deck is another prominent feature of the 917.273134. With a 42-inch cutting width, it enables users to quickly and efficiently cover large areas of grass. The deck features a three-blade system that ensures a clean and even cut, minimizing the need for multiple passes and reducing the overall mowing time. Additionally, the height of the cutting deck is adjustable, allowing users to choose the perfect grass length for their specific lawn needs.

User comfort and control are essential elements of the Craftsman 917.273134 design. It boasts a comfortable high-back seat that provides excellent support, especially during longer mowing sessions. The tractor is equipped with an intuitive dashboard displaying essential information, such as fuel level and engine status, allowing users to monitor the tractor’s health easily.

Moreover, the Craftsman 917.273134 integrates advanced technologies, such as an automatic transmission system that provides seamless gear shifting, allowing users to maintain optimal speed according to the terrain without manually shifting gears. This feature greatly enhances maneuverability and ease of use, making it accessible for operators of all skill levels.

Safety is also a priority in the design of this lawn tractor. It is equipped with safety features such as a automatic shutoff when the operator leaves the seat, preventing accidents while in operation. The durable construction of the Craftsman 917.273134 ensures its longevity and reliability, making it a worthy investment for any homeowner seeking a quality lawn care solution.

In summary, the Craftsman 917.273134 is a versatile and powerful lawn tractor that effectively meets the needs of today’s homeowners. With its robust engine, efficient cutting system, user-friendly design, and advanced technologies, it stands out as a top choice for maintaining lush and healthy lawns.
Top Page Image Contents