Craftsman 917.28746 owner manual Problem Cause Correction

Page 17

TROUBLESHOOTING CHART:

TROUBLESHOOTING CHART:

See appropriate

section in manual unless directed to Sears service center

See appropriate section in manual unless directed to Sears service center

PROBLEM

CAUSE

CORRECTION

PROBLEM

CAUSE

CORRECTION

Loss of poWer (continued)

6.

Faulty

spark

plug.

7.

Dirty fuel filter.

8.

Stale

or dirty

fuel.

9.

Water

in fuel.

 

10. Spark plug wire loose.

6.Clean and regap or change spark plug.

7.Replace fuel filter.

8.Empty fuel tank and refill tank with fresh, clean gasoline.

9.Emptyfuel tank and carbure- tor, refill tank with fresh gas-

olineand replace fuel filter. to. Connect and tighten spark

Mower blades will 1.

Obstruction

in clutch

not rotate

mechanism.

 

2.

Worn/damaged mower drive

 

belt.

 

 

3.

Frozen

idler

pulley.

4.

Frozen

blade mandrel.

5.

Mower

belt off engine pulley.

1.Removeobstructioil.

2.Replace mower drive belt.

3.Replace idler pulley.

4.Contact a Sears or other qualified service center.

3. Install belt on engine pulley.

11.

Dirty engine

air screen/fins.

12.

Dirty/clogged

muffler.

13. Loose or damaged wiring.

14. Carburetor out of adjustment.

15. Engine valves out of

 

adjustment.

 

plug wire.

11.Clean engine air screen/fins.

12.Clean/replace muffler.

13.Check all wiring.

14.See "To Adjust Carburetor"

in Service and Adjustments section.

15.Contact a Sears or other qualified service center.

Poor grass discharge

1.

Engine speed too slow.

2.

Travel speed

too fast.

3.

Wet grass.

 

4.

Mower not level.

5.

Low/uneven

tire air pressure.

6.

Worn, bent or loose blade.

1. Place throttle control in

 

"FAST" position.

2.

Shift to slower speed.

3. Allow grass to dry before

 

mowing.

4.

Level mower.

5.

Check tires for proper air

 

pressure.

6.

Replace/sharpen blade .

Excessive

1.

.

Worn, bent or loose blade.

vibration

2.

Bent blade mandrel.

 

 

3.

Loose/damaged partes).

1.Replace blade. Tighten blade bolt.

2.Contact a Sears or other qualified service center.

3.Tighten loose partes). Replace damaged parts.

7.

Buildup of grass, leaves and

 

trash under

mower.

8.

Mower

drive

belt worn.

9.

Blades

improperly installed.

10. Improper blades used.

 

Tighten

blade bolt.

 

7. Clean underside of mower

 

housing.

 

 

 

8.

Replace

mower

drive

belt.

9.

Reinstall

blades

sharp

edge

 

down.

 

 

 

10. Replace with blades listed

Engine dies when tractor is shifted into reverse

1. Reverse operation system

(ROS) is not "ON" while

mower or other attachment

is engaged.

1. Turn ignition key to

ROS "ON" position.

See Operation section.

11. Clogged mower vent

holes from buildup of grass,

leaves, and trash around

mandrels.

in this

manual.

11. Clean around mandrels to

open

vent holes.

Engine continues to run when operator leaves seat with attachment clutch engaged

1. Faulty operator-safety

presence control system.

1. Check wiring, switches and

connections. If not corrected,

contact a Sears or other

qualified service center.

Headlight(s) not working

(if so equipped)

1.

Ught switch

is "OFF".

2.

Bulb(s) or lamp(s) burned out.

3.

Faulty light

switch.

4.

Loose or damaged wiring.

5.

Blown fuse.

 

1.Turn light switch "ON".

2.Replace bulb(s) or lamp(s).

3.Check/replace light switch.

4.Check wiring and connections.

5.Replace fuse.

Poor cut. uneven

1.

Worn,

bent or loose blade.

1. Replace blade. Tighten blade

 

2.

Mower

deck not level.

bolt.

 

 

2. Level mower deck.

.

 

 

 

 

 

3.Buildup of grass, leaves, and 3. Clean underside of mower

trash under

mower.

housing.

 

 

4. Bent blade

mandrel.

4. Contact

a Sears

or other

 

 

qualified

service

center.

5.Clogged mower deck vent 5. Clean around mandrels to

from build-up of grass, leaves,

open vent holes.

and trash around mandrels.

 

Battery will not charge

Loss of drive

1.

Bad battery

cell(s).

2.

Poor cable

connections.

3.

Faulty regulator

 

(if so equipped).

4.

Faulty alternator.

1.

Freewheel

control in

 

"disengaged"

position.

2. Motion drive belt worn,

 

damaged,

or broken.

3.

Air trapped

in transmission

 

during shipment or servicing.

.

1.Replace battery.

2.Check/clean all connections.

3.Replace regulator.

4.Replace alternator.

1.Place freewheel control in "engaged" position.

2.Replace motion drive belt.

3.Purge transmission.

Engine "backfires' when turning engine "OFF"

1. Engine throttle control not set 1. Move throttle control

between half and full speed

between

half and full speed

(fast) position before stopping

(fast) position before

engine.

 

 

stopping

engine.

32

33

Image 17
Contents SEARS, Roebuck and CO., Hoffman ESTATES, IL 60179 U.S.A Your HomeSafety Rules II. Slope Operation ServiceIV. Towing III. ChildrenSears Installation Service Product SpecificationsCustomer Responsibilities Repair Protection AgreementsInstall Mower and Drive Belt Tools Required for AssemblyAssemble Front Wheel to Mower To Remove Tractor fromCheck Deck Levelness Check Tire Pressure IchecklistCheck for Proper Position ALL BeltsKnow Your Tractor Attachment Clutch SwitchHOW to USE Your Tractor To Start Engine Before Starting the EngineAutomatic Transmission Warm UP Purge TransmissionMowing Tips Tractor Lubrication ChartGeneral Recommendations Before Each USEEngine Transaxle Pump FluidTo Install Mower CleaningVice or Adjustments Tractor To Remove MowerTo Replace Motion Drive Belt To Adjust Attachment ClutchTo Replace Mower Drive Belt To Check Brake Replacing BatteryFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsBattery Troubleshooting ChartEngine OtherProblem Cause Correction Suggested Guide for Sighting Slopes for Safe Operation

917.28746 specifications

The Craftsman 917.28746 is a well-regarded lawn tractor known for its reliability and performance, making it a preferred choice for homeowners looking to maintain their yards efficiently. One of the standout features of this model is its 18.5 horsepower engine, which is designed to provide ample power for a variety of mowing tasks. The engine is paired with a smooth hydrostatic transmission that allows for seamless speed adjustments and maneuverability, ensuring that users can navigate through different terrain with ease.

This lawn tractor sports a 42-inch cutting deck, ideal for medium to large-sized lawns. The deck is designed to offer a clean and even cut, featuring twin blades that enhance the quality of the mowing experience. Users have the option to adjust the cutting height, giving them control over how short or long they want their grass to be. This versatility in cutting heights accommodates different grass types and seasonal variations.

Ergonomics play a crucial role in the design of the Craftsman 917.28746. The tractor comes with an adjustable seat that provides comfort during extended mowing sessions, allowing users to fine-tune their riding position. Additionally, the placement of the steering wheel and controls is intuitive, making it easier for operators to engage and disengage functions such as the cutting deck and cruise control without unnecessary effort.

One of the notable technologies incorporated in the Craftsman 917.28746 is its Mulching Capability. This feature allows grass clippings to be finely chopped and redistributed back onto the lawn, fostering a natural fertilization process. Those looking for a clean-cut finish can easily switch to side discharge or bagging options based on their lawn care needs.

Furthermore, the robust construction of the Craftsman 917.28746 ensures longevity and durability. The steel frame and heavy-duty components are capable of withstanding regular use, making it a worthy long-term investment for lawn care. With a blend of power, comfort, and advanced features, the Craftsman 917.28746 stands out as an excellent tool for homeowners committed to maintaining beautiful landscapes with minimal effort. It delivers a user-friendly experience while addressing the diverse demands of lawn maintenance.