Craftsman 917.275632 manual Blade Care, Blade Removal, To Sharpen Blade

Page 16

TRACTOR

Always observe safety ruleswhen per-

forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then

brake must be checked and adjusted. (See "TO ADJUST BRAKE" in the Service and

Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See "PRODUCT SPECIFICATIONS" section of this manual).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rub- ber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts

dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND

REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as de- scribed, repair the problem immediately.

•The engine should not start unless the

brake pedal is fully depressed, and the attachment clutch control is in the disen-

gaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never op- erate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ig- nition switch in the engine "ON" position and the attachment clutch is engaged, any attempt by the operator to shift into reverse should shut off the engine.

ROS "ON" Position Engine "ON" Position (Normal Operating)

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch is engaged, any attempt by the operator to shift into

reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL

1.Raise mower to highest position to al- low access to blades.

2.Remove blade bolt, lock washer and flat washer securing blade.

3.Install new or resharpened blade

with trailing edge up towards deck as shown.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Reassemble blade bolt, lock washer and flat washer in exact order as shown.

5.Tighten blade bolt securely (27-35 Ft.

Lbs. torque).

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approve bolt shown in the Repair Parts.

Trailing

 

Mandrel As_

Edge Up_

Blade

Center

 

 

Flat

 

 

Lock Washer

 

 

_-Blade Bolt

TO SHARPEN

BLADE

NOTE: We do not recommend sharp-

ening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause

excessive vibration and eventual damage to mower and engine.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Crrftsmrn Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation Service Safe Handling of Gasoline II. Slope OperationII1. Children IV, TowingGeneral Service Customer Responsibilities Repair Protection AgreementsAdjust Seat Check BatteryUnpack Carton Check Deck Levelness Check for Proper Position of ALL BeltsCheck Brake System To Drive Tractor OFF SkidFast Reverse Tractor To SET Parking Brake To USE Throttle ControlStopping To Move Forward and BackwardUsing the Reverse Operation System Operating in ReverseROS on To Operate MowerMents ADD GasolineMowing Tips OAT General RecommendationsBlade Removal Blade CareTo Sharpen Blade Battery Clean AIR Screen Engine OIL FilterAIR Filter MufflerTo Install Mower Service or AdjustmentsTo Remove Mower To Level Mower Housing To Replace Mower Blade Drive BeltTo Check and Adjust Brake To Adjust BrakeTo Check Brake To Replace Motion Drive BeltMent To Remove Wheel for RepairsReplacing Battery To Replace Headlight BulbInterlocks and Relays To Remove Hood and Grill AS- SemblyTo Adjust Carburetor Preliminary SettingFinal Setting EngineEngine OIL Fuel SystemCylinders Problem Cause3ORRECTION Start EngineProblem CorrectionProblem Cause OFFSchematic Tractor - Model NumberElectrical Part Description Tractor - Model Number 917,275632 Chassis and Enclosures Tractor - Model Number 917.275632 Chassis and Enclosures KEY Part DescriptionPage Tractor - Model Number 917,275632 Ground Drive 875Steering KEY Part Description Optional Equipment Spark ArresterTractor - Model Number Seat Assembly KEYWheels & Tires DecalsKEY Part NO. no Lift Assembly Tractor - Model4oi€ Tractor - Model Number 917,275632 Mower DeckTractor - Model Number Mower Deck 850857Numbers Here KEY Part NO. no Description144I 24o Manual 697127 Crankshaft Choke 690947 Seal-Oil KEY Part Description Page Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXYour Home

917.275632 specifications

The Craftsman 917.275632 is a versatile and reliable lawn mower that has impressed homeowners with its powerful performance and ease of use. This model is popular for its efficiency in maintaining yards of various sizes, making it a preferred choice among gardening enthusiasts and landscaping professionals alike.

One of the standout features of the Craftsman 917.275632 is its 21-inch cutting deck, which allows for wide mowing coverage while still being agile enough to navigate tight spaces. The cutting deck is made from durable materials to withstand rigorous use while ensuring a clean and precise cut. Its adjustable cutting height, ranging from 1.25 inches to 4 inches, offers users the flexibility to customize their lawn's appearance based on personal preference and seasonal requirements.

Equipped with a powerful Briggs & Stratton engine, the Craftsman 917.275632 delivers robust performance that can tackle thick grass and uneven terrain with ease. The engine features reliable starting technology, ensuring that users can get started quickly without hassle. The mower's self-propelling capabilities provide an added advantage, allowing less manual effort for users while navigating slopes or large yards.

Another notable characteristic is the mower's versatility in grass discharge options. Users can choose between mulching, bagging, or side discharge, providing flexibility based on seasonal needs. The mulch kit, in particular, promotes a healthier lawn by returning nutrients to the soil, creating a sustainable and eco-friendly mowing solution.

Efficiency is further enhanced through ergonomic design features, including comfortable handles that reduce vibrations and fatigue during extended use. The mower's compact size facilitates easy storage, making it an excellent fit for homeowners with limited garage space.

In terms of technology, the Craftsman 917.275632 incorporates reliable safety features, such as a blade brake that stops the blade quickly when released, ensuring user safety while mowing. The easy-to-maneuver design, coupled with its power and functionality, attracts users seeking a dependable lawn care solution.

Overall, the Craftsman 917.275632 is a well-rounded lawn mower that combines power, versatility, and user-friendly features, making it an outstanding option for anyone looking to maintain a well-kept lawn. Whether you're edging around flower beds or tackling the entire yard, this model is designed to deliver impressive results consistently.
Top Page Image Contents