Craftsman 917.272762 manual Problem Cause Correction

Page 32

TROUBLESHOOTING CHART:

See appropriate section in manual unless directed to Sears service center

PROBLEM

CAUSE

 

 

CORRECTION

 

Mower blades will 2.

Worn/damaged

mower

2.

Replace

mower

drive belt.

not rotate (con't)

drive belt.

 

 

 

 

 

3.

Frozen

idler pulley.

3.

Replace

idler pulley.

4.

Frozen

blade

mandrel.

4.

Contact

aSears

or other

 

 

 

 

 

qualified

service

center.

Poor grass1. Engine speed too slow. discharge

2.Travel speed too fast.

3.Wet grass.

4.Mower deck not level.

5.Low/uneven tire air pressure.

6.Worn, bent or loose blade.

7.Buildup of grass, leaves and trash under mower.

8.Mower drive belt worn.

9.Blades improperly installed.

10.Improper blades used.

11.Clogged mower deck vent holes from buildup of

grass, leaves, and trash around mandrels.

1.Place throttle control in "FAST" position.

2.Shift to slower speed.

3.Allow grass to dry before mowing.

4.Level mower deck.

5.Check tires for proper air pressure.

6.Replace/sharpen blade. Tighten blade bolt.

7.Clean underside of mower housing.

8.Replace mower drive belt.

9.Reinstall blades sharp edge down.

10.Replace with blades listed in this manual.

11.Clean around mandrels to open vent holes.

Headlight(s)

not

1.

Switch

is "OFF".

 

1.

Turn switch

"ON".

working

 

2.

Bulb(s) or lamp(s) burned out

2.

Replace

bulb(s)

or lamp(s).

(if so equipped)

3.

Faulty

light

switch.

 

3.

Check/replace

light switch.

 

 

4.

Loose

or damaged

wiring.

4.

Check wiring and connec-

 

 

 

 

 

 

 

 

 

tions.

 

 

 

 

 

5.

Blown

fuse.

 

 

5.

Replace

fuse.

 

Battery will

not

1.

Bad battery

 

cell(s).

 

1.

Replace

battery.

charge

 

2.

Poor cable

connections.

2.

Check/clean

all connec-

 

 

 

 

 

 

 

 

 

tions.

 

 

 

 

 

3.

Faulty

regulator

 

3.

Replace

regulator.

 

 

4.

(if so equipped).

 

 

 

 

 

 

 

 

Faulty

alternator.

 

4.

Replace

alternator.

Loss of drive

1.

Freewheel

control

in

1.

Place freewheel

control in

 

 

2.

"disengaged"

position.

 

"engaged"

position.

 

 

Motion

drive

belt worn,

2.

Replace

motion

drive belt.

 

 

3.

damaged,

or broken.

 

 

 

 

 

 

 

Air trapped

 

in transmission

3.

Purge transmission.

 

 

 

during

shipment or

 

 

 

 

 

 

servicing.

Engine "backfires"

when turning engine "OFF"

1.Engine throttle control not set at "SLOW"

position for 30 seconds before stopping engine.

1.Move throttle control to

"SLOW" position and allow to idle for 30 seconds before

stopping engine.

32

Image 32
Contents ICRnFTZMnWl Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation II. Slope OperationIII. Children IV. ServiceDo not Page Home Sears Installation ServiceRepair Protection Agreements Steering Wheel Howto SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Before Removing Tractor from Skid Attach Steering WheelSee Operation section for location and function of controls Check BatteryTo Drive Tractor OFF Skid Install Mulcher Plate Check Deck LevelnessDischarging Check for Proper Position of ALL Belts@@@@@ Know Your Tractor AmmeterAttachment Clutch Lever Used AttachmentHOW to USE Your Tractor To SET Parking BrakeGround Drive EngineTo Operate on Hills To Adjust Gauge WheelsTo Operate Mower Before Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineAutomatictransmissionwarm UP Purge TransmissionMowing Tips Mulching Mowing TipsCheck engine oil level Check brake operation General RecommendationsBefore Each USE Battery TractorOperator Presence System Blade RemovalLubrication EngineTransaxle Pump Fluid Engine OIL Filter Clean AIR ScreenAIR Filter Cleaning MufflerSpark Plugs Protect painted surfaces with auto- motive type waxService or Adjustments To Install MowerTractor To Remove MowerBelt Removal To Level Mower HousingSIDE-TO-SIDE Adjustment Belt Installation Transaxle Motion Control LE VER Neutral Adjustment Motion control lever has been presetTransmission Removal Replacement To Adjust Steering Wheel Align MentReplacing Battery To Attach Jumper CablesInterlocks and Relays To Replace FusePreliminary Setting To Adjustthrottle Control CableTo Adjust Carburetor Battery Fuel SystemEngine OIL CylindersCause Troubleshooting ChartProblem Troubleshooting Chart CausecorrectionProblem Cause Correction Tractor - Model Number Schematic 0EO OII1Tractor - Model Number ElectricalTractor - Model Number Electrical KEY Part DescriptionTractor - Model Number Chassis and Enclosures 175049 Grille Lens Asm Tractor - Model Number Ground Drive Tractor -- Model Number Ground Drive CADTractor - Model Number 917.272762 Steering Assembly KEY Part Description Engine Tractor - Model Number Seat Assembly BoltTractor -- Model Number Decals Wheels Tires KEY PartTractor -- Model Number Lift Assembly Tractor - Model Number Mower Deck 177563 Bracket, Deflector 105304X Cap, Sleeve 123713X 150 627 1o8o 783÷1 4741 Gasket-Crankcase KEY Part NO. no Suggested Guide for Sighting Slopes for Safe Operation 6E/A R