Craftsman 917.370620 owner manual Lawn Mower, Drive Wheels

Page 13

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check front drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash,

grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both front wheels.

1.Remove hubcaps, Iocknuts & washers.

2.Remove wheels from wheel adjusters.

3.Remove any trash or grass cuttings from inside the dust cover, pinion and/ or drive wheel gear teeth.

4.Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a Sears or other qualified service center.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade. A CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is haz- ardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and

mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware

(bolt, lock washer, hardened washer). NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on blade adapter.

3.Be sure trailing edge of blade (opposite sharp edge) is up toward the engine.

4.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

5.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Key

Crankshaft

Lockwasher

 

 

Blade

 

....',,

Blade

 

_

 

 

bolt

Hardened

:_,:,,,",

/ \ '\

 

 

washer

Trailing

edge

retainer

TO SHARPEN BLADE

NOTE: We do not recommend sharp-

ening blade - but if you do, be sure the blade is balanced. An unbalanced blade

will cause eventual damage to lawn mower or engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with it.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain m a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Center hole

5/8" bolt or pin

13Blade

Image 13
Contents Craftsman Your Safety is Involved Yearfull Warranty on Craftsman Lawn MowerIV. Safe Handling of Gasoline General OperationDo not 030 General ServiceLawn Mower Performance Lawn Mower MaintenanceTo Unfold Handle To Remove Mower from CartonTo Assemble Grass Catcher MowingKnow Your Lawn Mower Meets Cpsc Safety RequirementsHOW to USE Your Lawn Mower To Empty Grass Catcher Before Starting EngineFor Rear Bagging ADD OILTo Start Engine To Stop EngineMowing Tips Mulching Mowing TipsBefore Each USE General RecommendationsLubrication Before After EveryDrive Wheels Lawn MowerGrass Catcher To Clean AIR FilterGear Case EngineClean Under Drive Cover CleaningMuffler Spark PlugRear Deflector To Adjust HandleTo Remove Drive Belt To Replace Drive BeltCarburetor EngineHandle Fuel System OtherEngine OIL CylinderCause ProblemCorrection Need More HELP?SU Seguridad Esta Comprometida Sears, Roebuck and Co., Hoffman Estates, ILIII. Ninos OperacionII. Operacion Sobre LAS Cuestas HacerRJ19LM SAEMantenimiento DE LA Segadora Rendimiento DE LA SegadoraComo Preparar SU Segadora Cumple CON LOS Requisitos DE Seguridad DE LA Cpsc Producto. Aprenda y comprenda sus significadosVelocidad DEL Motor Como Usar SU SegadoraImportante Antes DE Hacer Arrancar EL MotorPara Parar EL Motor Para Hacer Arrancar EL MotorConsejos Para Segar Y ACOL- Char Onsejos Para SegarAntes DE Cada USO Recomendaciones GeneralesLubricacion Tabla DE LubricacionSegadora Motor Lubricacion Limpie Debajo DE LA Cubierta DE LA IMPULSI6N LimpiezaDesviador Trasero Para Ajustar LA Altura DE CortePara Remover Correa DE Impulsion Para Ajustar EL MangoVelocidad DEL Motor MotorCarburador SegadoraCilindro Problema CausaOtros Causa ProblemaLvl Iii m Iii a ILli COo \ \ LL04 N7 W n n n n7 n7 U n 000 Oonon Briggs & Stratton 4-CYCLE Engine 471188% ¸ oi 104 137 617 KEY Part Description 404 690272 Washer Governor Serifs

37062, 917.370620 specifications

The Craftsman 917.370620 and 917.37062 are robust riding lawn mowers designed for efficiency and ease of use in maintaining residential lawns. These models are particularly popular among homeowners who appreciate their performance, reliability, and innovative features that simplify the task of lawn care.

One of the standout characteristics of the Craftsman 917.370620 is its powerful engine. Equipped with a reliable Briggs & Stratton engine, it delivers impressive horsepower, ensuring that users can tackle even the toughest mowing conditions effortlessly. This reliable engine not only provides ample power for cutting through thick grass but also ensures longevity and dependable performance year after year.

Cutting precision is another highlight of these models. The mowers come with a wide cutting deck, typically measuring 42 inches, which allows for efficient mowing of substantial areas without the need for excessive back-and-forth passes. The deck height can be easily adjusted to accommodate different grass lengths and types, giving users the flexibility to achieve their desired lawn height.

Both models feature a hydrostatic transmission, allowing for smooth speed control without the need for clutching or shifting gears. This technology makes maneuvering around obstacles like trees and flower beds easier and provides a more comfortable experience for the operator. The intuitive control layout further enhances usability, enabling quick adjustments while on the move.

In addition to their performance capabilities, the Craftsman 917.370620 and 917.37062 are designed with user comfort in mind. They come equipped with ergonomically designed seats that provide support during long mowing sessions. The inclusion of a steering wheel makes handling the mower comfortable, reducing fatigue associated with prolonged use.

Durability is another critical feature of these mowers. The robust construction is designed to withstand the wear and tear common in lawn care equipment. With features like a reinforced frame and heavy-duty wheels, users can rely on these mowers for consistent performance over time.

Moreover, the mowers offer optional attachments such as mulching kits and baggers, enhancing their versatility for various lawn care tasks. Whether it's mulching grass clippings or collecting leaves in the fall, these attachments elevate the mowing experience and extend the equipment's functionality.

In conclusion, the Craftsman 917.370620 and 917.37062 riding mowers are engineered to deliver power, precision, and comfort. With their strong engines, wide cutting decks, user-friendly controls, and durable build, they stand as excellent choices for homeowners looking to maintain their lawns efficiently and effectively.