Craftsman 917.37134 owner manual Lubrication Chart, Tires

Page 11

LUBRICATION CHART

Wheel

adjuster (on each wheel)

Handle bracket mounting pins

_ Spray lubricant

See "ENGINE" in Maintenance section.

IMPORTANT: Do not oil or grease plastic

wheel bearings. Viscous lubricants will attract dust and dirt that will shorten the life of

the self-lubricating bearings. If you feel they must be lubricated, use only a dry, powdered graphite type lubricant sparingly.

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade.

_i, CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and

mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware (bolt, lock washer, hardened washer).

NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

3.Be sure trailing edge of blade (opposite sharp edge) is up toward the engine.

4.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

5.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

•The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated.

If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Key

Crankshaft

Lockwasher _

i

bolt Hardened d'ge

washerCrankshaft

TO SHARPEN BLADE

NOTE: We do not recommend sharpening

blade - but if you do, be sure the blade is balanced. An unbalanced blade will cause

eventual damage to mower or engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, drive a nail into a beam or wall. Leave about one inch of

the straight nail exposed. Place center hole of blade over the head of the nail.

If blade is balanced, it should remain in a horizontal position. If either end of the

blade moves downward, sharpen the

11heavy end until the blade is balanced.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Crrftsmrn Sears, Roebuck and Co., Hoffman Estates, IL Year Full Warranty on Craftsman Lawn MowerIII. Children General OperationII. Slope Operation Do notRJ19LM General ServiceAPI SG-SL Lawn Mower Performance Lawn Mower MaintenanceSears Installation Service To Unfold Handle To Install AttachmentsCarton Know Your Lawn Mower Meets Cpsc Safety RequirementsBefore Starting Engine ADD OIL HOW to USE Your Lawn MowerMulching Mowing Tips To Stop EngineTo Start Engine Mowing TipsLU Brication USE HOURSORSEASO.HOURSSTORAGEGeneral Recommendations Before Each USETires Lubrication ChartMuffler Engine LU BricationTo Adjust Handle CleaningLawn Mower To Adjust Cutting Height Engine Fuel System EngineLawn Mower Other ProblemEngineoil CylinderCause ProblemDespues de manipularlos III. Ninos OperacionHacer No HacerRJ 19LM ServicioSAE Mantenimiento DE LA Segadora Acuerdos de Protecci6n para la Reparaci6nMY-HOME Rendimiento DE LA SegadoraPara Instalar LOS Accesorios Para Remover LA Segadora DE LA Caja DE CartonComo Preparar SU Segadora Para Desdoblar EL Mango LevantarBarra de control que exige la presencia del Familiaricese CON SU SegadoraCumple CON LOS Requisitos DE Seguridad DE LA Cpsc Importante Como Usar SU Segadora Velocidad DEL MotorAntes DE Hacer Arrancar EL Motor Agregue AceiteConsejos Para Segar Y Acolchar Consejos Para SegarPara Parar EL Motor Para Hacer Arrancar EL MotorLubricacion Antes DE Cada USOSegadora Tabla DE LubricacionFiltro DE Aire RecogedordecospedMotor Para Cambiar EL Aceite DEL MotorPara Ajustar EL Mango LimpiezaSegadora Para Ajustar LA Altura DE CorteImportante Es importante evitar que MotorMango Motor Sistema DE CombustibleNo arranca Problema Causa CorreccionAceitedelmotor Problema Causa Craftsman Rotary Lawn MOWER- Model Number 917.371340 Craftsman Rotary Lawn Mower - Model NumberShort Block Briggs & Stratton 4-CYCLE EngineModel Number 10T802-0708-E1 Operators Manual Replacement Engine Emissions Label Repair ManualKEY Part NO. NO. Description KEY Part Description KEY PartDescription Service Notes Service Notes Your Home

917.37134 specifications

The Craftsman 917.37134 is a versatile and powerful lawn mower designed for both residential and commercial mowing needs. Known for its reliability and efficiency, this model has become a popular choice among homeowners and landscapers alike.

One of the standout features of the Craftsman 917.37134 is its robust engine. It is equipped with a reliable 21-inch cutting deck, powered by a dependable gas engine. This provides the necessary power and torque to tackle tough grass and uneven terrain with ease. The mower’s engine is designed for easy starting and smooth operation, minimizing downtime during lawn care.

Another key characteristic of the Craftsman 917.37134 is its innovative cutting technology. The mower employs a three-in-one cutting system, allowing users to choose between side discharge, mulching, or bagging clippings. This versatility means that users can manage their lawn maintenance effectively, whether they prefer leaving the clippings on the lawn for added nutrients or collecting them for disposal.

The Craftsman 917.37134 also features adjustable cutting height settings, allowing operators to customize the grass height according to their preferences or seasonal requirements. This ensures that the lawn can receive the right amount of care throughout the year, promoting healthier growth and appearance.

To enhance user convenience, the mower is designed with a comfortable grip handle and is easy to maneuver. Its lightweight construction allows for effortless handling and turning, reducing fatigue during extended mowing sessions. The adjustable handle height further improves ergonomics, meeting the needs of various users.

Durability is another hallmark of the Craftsman brand, and the 917.37134 is no exception. Its sturdy construction and high-quality materials ensure it can withstand the rigors of regular lawn maintenance while providing longevity. Maintenance is also simplified with easy access to the engine and deck components, making it user-friendly for anyone who prefers to conduct their own upkeep.

In conclusion, the Craftsman 917.37134 is a well-rounded lawn mower that combines power, versatility, and ease of use. It’s equipped with advanced cutting technology, a durable design, and features that enhance the mowing experience, making it a reliable choice for anyone looking to maintain their lawn effectively. Whether for personal or professional use, this mower stands out in its class.
Top Page Image Contents