Craftsman 917.376676 owner manual Lawn Mower

Page 13

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

,Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check front drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash,

grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both front wheels.

1.Remove hubcaps, Iocknuts & washers.

2.Remove wheels from wheel adjusters.

3.Remove any trash or grass cuttings

from inside the dust cover, pinion and/ or drive wheel gear teeth.

4.Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a Sears or other qualified service center.

BLADE CARE

For best results, blade must be kept sharp. Replace a bent or damaged blade.

ACAUTION: Use only a replacement blade approved bythe manufacturer of your mower. Using a blade not approved by the manu- facturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and mower housing to prevent blade from

turning when removing blade bolt. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade & attaching hardware (bolt, lock washer & hardened washer).

TO REPLACE BLADE

1.Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

2.Be sure the trailing edge of blade (oppo- site sharp edge) is up toward the engine.

3.Install the blade bolt with the lock washer and hardened washer into

blade adapter and crankshaft.

4.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

Recommendedtighteningtorque:35-40ft.lbs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter KeyCrankshaft keyway

Lockwasher

Blade

Blade

bolt Hardened

/\

washer Trailing edge Crankshaft

TO SHARPEN BLADE

NOTE: We do not recommend sharpening the blade - but if you do, be sure the blade

is balanced. Care should be taken to keep the blade balanced. An unbalanced blade will

cause eventual damage to mower or engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, drive a nail into a beam or wall. Leave about one inch of

the straight nail exposed. Place center hole of blade over the head of the nail. If blade is balanced, it should remain in

a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

GRASS CATCHER

•The grass catcher may be hosed with water, but must be dry when used.

•Check your grass catcher often for dam-

age or deterioration. Through normal use it will wear. If catcher needs replac- ing, replace only with approved replace-

ment catcher shown in the Repair Parts section of this manual. Give the lawn

mower model number when ordering.

GEAR CASE

•To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season.

•The gear case is filled with lubricant to the

proper level at the factory. The only time the lubricant needs attention is if service

has been performed on the gear case. If lubricant is required, use Total Multis EP00 semi-liquid Grease or comparable

13 grade (quantity 1.15oz).

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Craftsman Year Full Warranty on Craftsman Lawn Mower IV. Safe Handling of Gasoline Do notRJ19HX API SG-SL SAERepair Protection Agreements To Remove Mower from Carton To Install AttachmentsTo Assemble Grass Catcher To Unfold HandleKnow Your Lawn Mower Meets Cpsc Safety RequirementsTo Adjust Cutting Height Rear Bagging To Convert MowerSide Discharging For Rear BaggingADD OIL To Empty Grass CatcherADD Gasoline To Start Engine To Stop EngineMowing TipsBefore Each USE General RecommendationsLubrication Lawn Mower AIR Filter CleaningMuffler Lawn Mower To Adjust Cutting Height High Position CleaningRotate CarburetorEngine Fuel System CorrectionEngine OIL CylinderCause Correction ProblemNeed More HELP? Garantia Reglas de Seguridad Hacer OperacionNo Hacer SERVlClO Rendimiento DE LA Segadora Cesped Cumple CON LOS Requisitos DE Seguridad DE LA Cpsc Familiaricese CON SU SegadoraPara EL Impulsion Cofao Usar SU Segadora Velocidad DEL MotorPapa Ajustar LA Altura DE Corte Segadoras CON Descarga Trasera Para Convertir LA SegadoraSegadoras CON Descarga Lateral Para Descarga LateralImportante Antes DE Hacer Arrancar EL Motor Agregue AceiteAgregue Gasolina Consejos Para Segar Y ACOL- Char Para Hacer Arrancar EL MotorLubricacion Antes DE Cada USOTabla DE LubricacionLlantas SegadoraRuedas DE Impulsion Cuidado DE LA CuchillaCaja DE Engranajes MotorFiltro DE Aire Para Limpiar EL Filtro DE AireLimpie Debajo DE LA Cubierta DE LA PRECAUCI6NImpulsion DE CorteMango Velocidad DEL MotorMotor Sistema DE Combustible ProblemaLlena si viene CausaOJ LO == N,, = \ \ = o × o Briggs & Stratton 4=CYCLE Engine 287Carburetor Gasket SET Operators Manual Carburetor Overhaul KITEngine Gasket SET Emissions LabelKEY Part Description 4259661Part Briggs & Stratton 4=CYCLE Engine KEYModel Number 122T02-3845-EA KEY Need More HELP?

917.376676 specifications

The Craftsman 917.376676 is a dependable and innovative lawn tractor designed for homeowners seeking efficiency and ease of use in maintaining their yards. Ideal for medium to large-sized lawns, this model combines power, comfort, and versatility, making it an excellent choice for DIY lawn care enthusiasts.

One of the standout features of the Craftsman 917.376676 is its robust 24 HP engine. This powerful engine delivers ample torque and speed, allowing users to tackle various terrains with confidence. The tractor's cutting-edge design optimizes fuel efficiency, providing longer run times without frequent refueling. Moreover, the engine's reliability is complemented by an automatic choke system, which ensures smoother starts in varying weather conditions.

The 917.376676 boasts a 50-inch cutting deck, an ideal size for efficiently covering large areas while still maneuvering around tight corners and obstacles. The cutting deck is equipped with six height adjustments, allowing users to customize the grass cutting height according to their preferences and the season's demands. This feature enhances versatility, enabling a clean and precise cut for a healthier lawn.

For ease of use, the Craftsman lawn tractor incorporates a smooth hydrostatic transmission. This technology allows for seamless speed adjustments without the need for manual shifting. Users can effortlessly accelerate or decelerate, making it easier to navigate different terrains or to slow down for intricate landscaping tasks.

Another notable characteristic of the 917.376676 is its comfortable seating and ergonomic design. The tractor features an adjustable high-back seat that offers ample support, reducing fatigue during extended use. Additionally, the strategically placed controls are intuitive and easy to reach, enhancing the overall user experience.

For added convenience, the Craftsman 917.376676 comes with a built-in mulching kit. This attachment allows for efficient grass clipping management, returning valuable nutrients back to the soil, which fosters healthier grass growth and reduces the need for additional fertilizers.

Safety features such as headlights for visibility in low-light conditions and a safety switch that kills the engine when the operator leaves the seat further enhance user confidence while operating the tractor.

In summary, the Craftsman 917.376676 represents a perfect combination of power, comfort, and cutting-edge technology. With its reliable engine, adjustable cutting deck, and user-friendly design, this lawn tractor is ideal for homeowners who prioritize efficiency and a well-manicured lawn. Whether tackling overgrown grass or maintaining a neat yard, the Craftsman 917.376676 is equipped to meet a variety of lawn care needs.
Top Page Image Contents