Craftsman 917.374358 owner manual Rear Deflector, To Remove Drive Belt, To Adjust Handle

Page 16

A WARNING: To avoid serious injury, before performing any service and adjustments:

1.Release control bar and stop engine.

2.Make sure the blade and all moving parts have completely stopped.

3.Disconnect spark plug wire from spark plug and place wire where it cannot come in

contact with plug.

LAWN MOWER

TO ADJUST CUTTING HEIGHT

See "TO ADJUST CUTTING HEIGHT" in the Operation section of this manual.

REAR DEFLECTOR

The rear deflector, attached between the rear wheels of your mower, is provided to minimize the possibility that objects will be thrown out of the rear of the mower into the operator mowing position. If the deflector becomes damaged, it should be replaced.

TO REMOVE DRIVE BELT

1.Remove screws securing rear baffle.

2.Turn lawn mower on its side with air filter and carburetor down.

3.Remove rear baffle from mower.

4.Remove blade bolt, Iockwasher, hard- ened washer and blade.

5.Remove debris shield.

6.Remove gearcase belt keeper.

7.Remove drive belt.

 

Gearcase

 

belt keeper

Rear

Belt

 

retainer

Gearcase

pulley

 

\\i

'}

Blade

 

adapter \

'}

Debris shield

TO REPLACE DRIVE BELT

1.Place new drive belt on gearcase pul- ley.

NOTE: Always use factory approved belt to assure proper fit and long life.

2.Reinstall gearcase belt keeper. Be sure the new drive belt is inside the

tabs of the gearcase belt keeper.

3.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned; and that the new drive belt is inside the tabs of the belt retainer.

4.Place rear baffle in mower housing.

5.Reinstall debris shield.

6.Reinstall blade.

7.Return mower to upright position.

8.Reinstall rear baffle screws.

TO ADJUST HANDLE

Your handle has three (3) height positions

-adjust to a height that suits you.

1.Remove knob and carriage bolt on one side of the lower handle.

2.While holding handle assembly, remove knob and carriage bolt from

opposite side, align hole in handle with desired hole in handle bracket and

reassemble bolt and knob and tighten securely.

3.Align opposite side of handle with same positioning hole and secure with bolt and knob.

Handle bracket

Knob

Bolt

Hardened

 

 

Blade

 

Blade

 

 

bolt

 

Lockwasher

16

 

 

Image 16
Contents Craftsman Yearfull Warranty on Craftsman Lawn Mower Your Safety is InvolvedIV. Safe Handling of Gasoline General OperationDo not General Service RJ19HXLawn Mower Maintenance Lawn Mower PerformanceTo Remove Mower from Carton To Unfold HandleTo Assemble Grass Catcher MowingMeets Cpsc Safety Requirements Know Your Lawn MowerEngine Speed Rear Bagging Side DischargingFor Rear Bagging To Convert MowerBefore Starting Engine Mulching Mowing Tips Mowing TipsSee Engine in Maintenance section General RecommendationsBefore Each USE LubricationLawn Mower Drive WheelsTo Clean AIR Filter Grass CatcherGear Case Engine LubricationCleaning Water Washout FeatureClean Under Drive Cover MufflerTo Adjust Handle Rear DeflectorTo Remove Drive Belt To Replace Drive BeltCarburetor HandleEngine Speed Fold Forward for Storage Mowing PositionProblem Cause Correction OtherFuel System Engine OILProblemcause Need More HELP?Sears, Roebuck and Co., Hoffman Estates, IL SU Seguridad Esta ComprometidaOperacion III. NinosII. Operacion Sobre LAS Cuestas HacerSAE RJ19HXMantenimiento DE LA Segadora Rendimiento DE LA SegadoraServicio de Instalaci6n Sears Como Preparar SU Segadora Familiaricese CON SU Segadora Producto. Aprenda y comprenda sus significadosVelocidad DEL Motor Como Usar SU SegadoraImpulsi6n Para Convertir LA Segadora Segadoras CON Descarga TraseraSegadoras CON Descarga Lateral Para Ensacamiento TraseroImportante Antes DE Hacer Arrancar EL MotorPara Parar EL Motor Onsejos Para Segar Consejos Para Segar Y ACOL- CharRecomendaciones Generales Antes DE Cada USOLubricacion Tabla DE LubricacionLlantas Ruedas DE IMPULSI6NCuidado DE LA Cuchilla Para Remover LA CuchillaMotor Derrubio DEL Agua LimpiezaLimpie Debajo DE LA Cubierta DE LA Impulsion Segadora Para Cambiar Correa DE IMPULSI6N Ajustar LA Altura DE CorteDesviador Trasero Para Remover Correa DE ImpulsionMotor Velocidad DEL MotorCarburador MangoProblema CausaAceite DEL Motor CilindroProblema Craftsman Rotary Lawn MOWER- Model KEY PartDESCRiPTiON SAE 30WPage KEY Part 84J Briggs & Stratton 4-CYCLE Engine19o 334 524 ? Model Number Briggs & Stratton Cycle EngineKEY Part Description 690959 Pin-Locating Need More HELP? Your Home