Craftsman 917.376531 owner manual Before Starting Engine

Page 11

TO EMPTY GRASS CATCHER

1.Lift up on grass catcher using the frame handle.

2.Remove grass catcher with clippings from under lawn mower handle.

3.Empty clippings from bag using both frame handle and bag handle.

NOTE: Do not drag the bag when empty- ing; it will cause unnecessary wear.

Grass catcher frame

_i, CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline

near an open flame.

,A CAUTION: Alcohol blended fuels (called gasohol or using ethanol or metha- nol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

BEFORE STARTING ENGINE

ADD OIL

Your lawnmower is shipped without oil in the engine. For type and grade of oil to use, see "ENGINE" in the Maintenance section of this manual.

i, CAUTION: DO NOT overfill engine with oil, or it will smoke heavily from the muffler on startup.

1.Be sure lawnmower is level.

2.Remove oil dipstick from oil fill spout.

3.You receive a container of oil with the unit. Slowly pour the entire container

down the oil fill spout into the engine. NOTE: Initial oi! fill requires only 18 oz. due to residual oil in engine from the manufacturers 100% quality testing. When changing oil you may need 20 oz.

4.Insert and tighten dipstick.

IMPORTANT:

• Check oil level before each use. Add oil

if needed. Fill to full line on dipstick.

Change the oil after every 25 hours of operation or each season. You may need to change the oil more often

under dusty, dirty conditions. See "TO CHANGE ENGINE OIL" in the Mainte-

nance section of this manual.

ADD GASOLINE

Fill fuel tank to bottom of tank filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of

87 octane. Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel fresh- ness.

Gasoline

filler cap

TO STOP ENGINE

To stop engine, release operator pres- ence control bar.

TO START ENGINE

NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal.

NOTE: Your engine is equipped with an automatic choke system. No priming or choking is required before starting.

To start engine, hold operator presence control bar down to the handle and turn

the start key.

IMPORTANT: Do not crank engine more than five continous seconds between each

time you try to start. Wait 5 to 10 seconds between each attempt.

To start engine using the rope starter, hold operator presence control bar down to the handle and pull starter handle quickly. Do not allow starter rope to snap back.

11

Image 11
Contents Craftsman Your Safety is Involved Yearfull Warranty on Craftsman Lawn MowerDo not General OperationIV. Safe Handling of Gasoline RJ19HX General ServiceLawn Mower Performance Lawn Mower MaintenancePosition To Remove Mower from CartonTo Unfold Handle MowingTo Assemble Grass Catcher To Prepare BatteryTo Install Attachments Know Your Lawn Mower Meets Cpsc Safety RequirementsHOW to USE Your Lawn Mower To Convert Mower Rear BaggingSide Discharging For Rear BaggingBefore Starting Engine Mowing Tips Mulching Mowing TipsBefore After Every General RecommendationsBefore Each USE LubricationDrive Wheels Lawn MowerEngine To Clean AIR FilterGrass Catcher Gear CaseSpark Plug CleaningClean Under Drive Cover MufflerRear Deflector Lawn Mower To Adjust Cutting HeightTo Adjust Handle To Remove Drive BeltForward for Storage Mowing Position CarburetorHandle Engine SpeedFuel System BatteryEngine OtherNeed More HELP? ProblemCause CorrectionSU Seguridad Esta Comprometida Sears, Roebuck and Co., Hoffman Estates, ILHacer OperacionIII. Ninos II. Operacion Sobre LAS CuestasRJ19HX SAEMantenimiento DE LA Segadora Rendimiento DE LA SegadoraPara Remover LA Segadora DE LA Caja DE Carton Como Preparar SU SegadoraPara Instalar LOS Accesorios Para Montar EL Recogedor DE CespedCumple CON LOS Requisitos DE Seguridad DE LA Cpsc Producto. Aprenda y comprenda sus significadosVelocidad DEL Motor Como Usar SU SegadoraPara Ensacamiento Trasero Para Convertir LA SegadoraSegadoras CON Descarga Trasera Segadoras CON Descarga LateralImportante Antes DE Hacer Arrancar EL MotorPara Parar EL Motor Consejos Para Segar Y ACOL- Char Onsejos Para SegarTabla DE Lubricacion Recomendaciones GeneralesAntes DE Cada USO LubricacionSegadora Motor Lubricacion Limpie Debajo DE LA Cubierta DE LA IMPULSI6N LimpiezaPara Ajustar EL Mango Para Ajustar LA Altura DE CorteDesviador Trasero Para Remover Correa DE ImpulsionSegadora MotorVelocidad DEL Motor CarburadorOtros ProblemaCausa Correccion ProblemaCraftsman Rotary Lawn Mower - Model Number KEY Part Description KEYPart Description Craftsman Rotary Lawn Mower - Model Number Craftsman Rotary Lawn Mower - Model Number 917o376531 Briggs & Stratton 4-CYCLE Engine Model Number 126T05-1252=EA Briggs & Stratton 4-CYCLE Engine Model Number 126T05=1252=EA 231 Valve Gasket SET Model Number 126T05=1252=EA KEY Part NO. NO. Description KEY Part Description Briggs & Stratton Cycle EngineModel NumberService Notes Service Notes Serifs

917.376531, 37653 specifications

The Craftsman 37653,917.376531 is a powerful and versatile power tool designed to meet the needs of both professional contractors and DIY enthusiasts. This tool stands out for its robust build quality and reliability, making it a cornerstone for any workshop or job site.

At the core of the Craftsman 37653 is a high-performance motor that provides impressive torque output, enabling users to tackle a wide variety of tasks with ease. Whether you're drilling, driving screws, or working with tough materials, this tool is engineered to deliver consistent performance. The variable speed settings allow users to adjust the speed according to the materials and tasks at hand, offering precision and control for intricate projects.

One of the standout features of the Craftsman 37653 is its ergonomic design. It boasts a comfortable grip that reduces fatigue during prolonged use, allowing users to work longer without discomfort. The tool's lightweight nature enhances portability, making it easy to transport from job to job or to work in confined spaces.

In terms of technologies, the Craftsman 37653 incorporates advanced battery management systems that ensure optimal battery life and performance. This allows users to work without worrying about frequent recharging, boosting productivity on the job. The quick-charge capability further enhances usability, giving users the ability to get back to work swiftly.

Durability is another key characteristic of the Craftsman 37653. Constructed from high-quality materials, it is designed to withstand tough working conditions, providing peace of mind to users who might operate in demanding environments. Additionally, the tool often comes with a protective case, which not only aids in storage but also provides extra protection during transport.

Safety is of paramount importance in power tools, and the Craftsman 37653 delivers with features such as a built-in safety lock. This prevents accidental activation, crucial for maintaining user safety during operation. Moreover, the design frequently includes LED lights that illuminate the work area, allowing for better visibility in low-light conditions.

In conclusion, the Craftsman 37653,917.376531 combines power, versatility, and safety, making it an indispensable tool for anyone serious about craftsmanship. Whether for home improvement or professional construction, its features, technologies, and characteristics cater to a broad spectrum of applications, ensuring it stands as a reliable partner in any project.