Craftsman 917.374061 owner manual Lawn Mower, Drive Wheels

Page 14

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check front drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash,

grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both front wheels.

1.Remove hubcaps, Iocknuts & washers.

2.Remove wheels from wheel adjusters.

3.Remove any trash or grass cuttings from inside the dust cover, pinion and/ or drive wheel gear teeth.

4.Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a Sears or other qualified service center.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade. A CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is haz- ardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and

mower housing to prevent blade from turning when removing blade bolt.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware

(bolt, lock washer, hardened washer). NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on blade adapter.

3.Be sure trailing edge of blade (opposite sharp edge) is up toward the engine.

4.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

5.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

•The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Key

Crankshaft

Lockwasher

Blade

Blade

 

 

 

bolt

Hardened

_

'_

 

washer

Trailing/edge

retainer

TO SHARPEN BLADE

NOTE: We do not recommend sharp-

ening blade - but if you do, be sure the blade is balanced. An unbalanced blade

will cause eventual damage to lawn mower or engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with it.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Center hole

5/8" bolt or pin

14Blade

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Craftsman Yearfull Warranty on Craftsman Lawn Mower Your Safety is InvolvedDo not General OperationIV. Safe Handling of Gasoline General Service RJ19HXLawn Mower Maintenance Lawn Mower PerformanceMowing To Remove Mower from CartonTo Unfold Handle PositionTo Assemble Grass Catcher To Prepare BatteryTo Install Attachments Meets Cpsc Safety Requirements Know Your Lawn MowerHOW to USE Your Lawn Mower For Rear Bagging Rear BaggingSide Discharging To Convert MowerBefore Starting Engine Mulching Mowing Tips Mowing TipsLubrication General RecommendationsBefore Each USE Before After EveryLawn Mower Drive WheelsGear Case To Clean AIR FilterGrass Catcher EngineMuffler CleaningClean Under Drive Cover Spark PlugTo Remove Drive Belt Lawn Mower To Adjust Cutting HeightTo Adjust Handle Rear DeflectorEngine Speed CarburetorHandle Forward for Storage Mowing PositionOther BatteryEngine Fuel SystemCorrection ProblemCause Need More HELP?Sears, Roebuck and Co., Hoffman Estates, IL SU Seguridad Esta ComprometidaII. Operacion Sobre LAS Cuestas OperacionIII. Ninos HacerSAE RJ19HXRendimiento DE LA Segadora Mantenimiento DE LA SegadoraComo Preparar SU Segadora Para Remover LA Segadora DE LA Caja DE CartonPara Montar EL Recogedor DE Cesped Para Instalar LOS AccesoriosProducto. Aprenda y comprenda sus significados Cumple CON LOS Requisitos DE Seguridad DE LA CpscComo Usar SU Segadora Velocidad DEL MotorSegadoras CON Descarga Lateral Para Convertir LA SegadoraSegadoras CON Descarga Trasera Para Ensacamiento TraseroImportante Antes DE Hacer Arrancar EL MotorPara Parar EL Motor Onsejos Para Segar Consejos Para Segar Y ACOL- CharLubricacion Recomendaciones GeneralesAntes DE Cada USO Tabla DE LubricacionSegadora Motor Lubricacion Limpieza Limpie Debajo DE LA Cubierta DE LA IMPULSI6NPara Remover Correa DE Impulsion Para Ajustar LA Altura DE CorteDesviador Trasero Para Ajustar EL MangoCarburador MotorVelocidad DEL Motor SegadoraOtros ProblemaCausa Problema CorreccionCraftsman Rotary Lawn Mower - Model Number 917.37406t KEY KEY PartNO. no Part DescriptionCraftsman Rotary Lawn Mower - Model Number 917.37406t Craftsman Rotary Lawn Mower - Model Number 917o37406t KEY Part Description22i 2o Briggs & Stratton 4-CYCLE Engine1386 23I Valve Gasket SET Briggs & Stratton Cycle Engine PTOKEY Part NO. NO. Description Service Notes Service Notes Serifs

37406, 917.374061 specifications

The Craftsman 917.374061 and 917.37406 are part of the renowned Craftsman lawn tractor series, known for their durability, efficiency, and user-friendly design. These riding mowers are crafted to make lawn care less of a chore and more of an enjoyable experience, blending technology and performance to meet the needs of homeowners.

One of the standout features of the Craftsman 917.374061 and 917.37406 is their powerful engine. Equipped with a robust Briggs & Stratton engine, these tractors offer reliable starting and high-performance operation. The engine provides ample power to handle both flat and uneven terrains, making it suitable for various lawn sizes and configurations.

The cutting deck of these models measures 42 inches, allowing for a wide cutting path that minimizes mowing time. The mower deck is built from high-quality steel, ensuring durability while delivering a clean and precise cut. Additionally, the deck features a height adjustment mechanism that allows users to choose their desired cutting height easily, enabling effective grass management across seasons.

Comfort is another key aspect of the Craftsman 917.374061 and 917.37406. These tractors are designed with an ergonomic seat and easy-to-reach controls to enhance the user experience. The spacious foot area and dashboard provide added comfort, allowing operators to mow for extended periods without discomfort.

For convenience, these models come with a convenient automatic transmission system. The hydrostatic drive allows for smooth and effortless speed control, making it easy to navigate around obstacles and tight spaces in the yard. This technology enhances maneuverability, making mowing a less daunting task, even for those new to lawn care.

Moreover, both models support an array of attachment options, expanding their versatility beyond just mowing. Users can easily connect baggers, trailers, and snow blowers, making these tractors useful year-round.

In summary, the Craftsman 917.374061 and 917.37406 are excellent choices for anyone looking for reliable, efficient, and user-friendly lawn tractors. With their powerful engines, durable cutting decks, and focus on operator comfort, they stand out in the competitive lawn care market. Whether you're maintaining a small garden or a larger yard, these Craftsman models are designed to meet a variety of landscaping needs with ease and efficiency.
Top Page Image Contents