Craftsman 917.37561 owner manual Lawn Mower

Page 12

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TIRES

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp

objects and other hazards that may cause tire damage.

DRIVE WHEELS

Check front drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means

trash, grass cuttings, etc. are in the drive wheel area and must be cleaned to free

drive wheels.

If necessary to clean the drive wheels, be sure to clean both front wheels.

1.Remove hubcaps, Iocknuts & washers.

2.Remove wheels from wheel adjusters.

3.Remove any trash or grass cuttings from inside the dust cover, pinion and/ or drive wheel gear teeth.

4.Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a Sears or other qualified service center.

GEAR CASE

•To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season.

•The gear case is filled with lubricant to

the proper level at the factory. The only time the lubricant needs attention is if

service has been performed on the gear case.

•If lubricant is required, use only ELF Multis EP00. Do not substitute.

BLADE CARE

For best results, mower blade must be kept sharp. Replace a bent or damaged blade.

_I, CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is hazardous, could damage your mower and void your warranty.

TO REMOVE BLADE

1. Disconnect spark plug wire from spark

plug and place wire where it cannot

come in contact with plug.

2. Turn lawn mower on its side. Make

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade and attaching hardware (bolt, lock washer, hardened washer).

NOTE: Remove the blade adapter and check the key inside hub of blade adapter. The key must be in good condition to work properly. Replace adapter if damaged.

TO REPLACE BLADE

1.Position the blade adapter on the en- gine crankshaft. Be sure key in adapter and crankshaft keyway are aligned.

2.Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

3.Be sure the trailing edge of blade (oppo- site sharp edge) is up toward engine.

4.Install the blade bolt with the lock washer and hardened washer into blade adapter and crankshaft.

5.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

•The recommended tightening torque is 35-40 ft. Ibs.

IMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with

approved bolt shown in the Repair Parts section of this manual.

Blade adapter

Key

Crankshaft

Lockwasher _

bolt Hardened

washer Trailing'edge Crankshaft

TO SHARPEN BLADE

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. An unbalanced blade will cause eventual damage to mower or engine.

• The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

• To check blade balance, drive a nail into a beam or wall. Leave about one inch of

the straight nail exposed. Place center hole of blade over the head of the nail.

sure air filter and carburetor are up.

3. Use a wood block between blade and

mower housing to prevent blade from

turning when removing blade bolt.

12

If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Crrftsmrn Year Full Warranty on Craftsman Lawn Mower General Operation II. Slope OperationDo not III. ChildrenGeneral Service API SG-SLRJ19LM Lawn Mower Maintenance Sears Installation ServiceLawn Mower Performance To Install Attachments CartonTo Unfold Handle Meets Cpsc Safety Requirements Know Your Lawn MowerImportant This Without OIL orHOW to USE Your Lawn Mower To Adjust Cutting HeightBefore Starting Engine ADD OILADD Gasoline To Stop EngineMowing Tips Mulching Mowing TipsLubrication Chart Spray lubricant See Engine in Maintenance sectionGeneral Recommendations Before Each USELawn Mower To Clean AIR Filter Element GrasscatcherEngine To Change Engine OILCleaning MufflerTo Remove Drive Belt To Adjust Handle Squeeze To AdjustTo Replace Drive Belt Rotate Engine Engine SpeedEngine Lawn MowerHandle Fuel SystemProblem CylinderOther CorrectionProblem CauseSears, Roebuck and Co., Hoffman Estates, IL Despues de manipularlosOperacion HacerNo Hacer III. NinosSAE Acuerdos de Protecci6n para la Reparaci6n MY-HOMERendimiento DE LA Segadora Mantenimiento DE LA SegadoraPara Remover LA Segadora DE LA Caja DE Carton Como Preparar SU Segadora Para Desdoblar EL MangoPara Instalar LOS Accesorios Familiaricese CON SU Segadora ImportanteCumple CON LOS Requisitos DE Seguridad DE LA Cpsc Barra de control que exige la presencia delComo Usar SU Segadora Velocidad DEL Motor Para Convertir LA SegadoraPara EL Impulsion Para Ajustar LA Altura DE CorteMotor Agregue Aceite Para Parar EL MotorPara Hacer Arrancar EL Motor Nsejos Para Segar Antes DE Cada USO TablaLlantas Ruedas DE ImpulsionRecogedordecosped MotorPara Cambiar EL Aceite DEL Motor Filtro DE AireLimpieza Limpie Debajo DE LA Cubierta DE LAImpulsion Segadora Para Ajustar LA Altura DE CortePara Cambiar Correa DE Impulsion Para Ajustar EL MangoMotor Velocidad DEL Motor Mango Motor Sistema DE CombustibleProblema Causa Aceite DEL MotorCorreccion No arrancaFuerza Mal corteDisparejo VibracionCraftsman Rotary Lawn MOWER- Model Number Craftsman Rotary Lawn Mower - Model Number KEY Part NO. noKEY Part DescriptionCraftsman Rotary Lawn MOWER- Model Number KEY Part Description Briggs & Stratton 4-CYCLE Engine Model Number 10T802-0708-EA Short BlockReplacement Engine Operators ManualEmissions Label Repair ManualKEY Part NO. NO. Description KEYPart NO. Description KEY Part Description Your Home

917.37561 specifications

The Craftsman 917.37561 is a powerful and versatile lawn tractor designed to cater to the needs of homeowners who require efficiency and reliability in lawn maintenance. This model is particularly respected for its performance, durability, and user-friendly features, making it an ideal choice for both small and large yards.

One of the standout features of the Craftsman 917.37561 is its robust engine. Powered by a 21 HP Briggs & Stratton engine, it delivers substantial power for tackling tougher mowing tasks. The engine is designed for easy starting and dependable performance, ensuring that users can efficiently care for their lawns without repeated interruptions. The automatic transmission adds convenience, allowing users to change speeds effortlessly, adapting to different mowing conditions.

The cutting deck of the Craftsman 917.37561 is another notable feature. It boasts a 42-inch deck size, providing an ample cutting width that maximizes efficiency during mowing sessions. The deck is constructed from durable materials, ensuring longevity and resistance to wear. Additionally, the deck features a deck wash port that allows for easy cleaning after mowing, maintaining the performance of the machine and extending its lifespan.

Moreover, the tractor is equipped with a tight turning radius, which enhances maneuverability around trees, flower beds, and other obstacles in your yard. This capability enhances its versatility, making it an attractive option for varied landscaping layouts.

Comfort is a priority in the design of the Craftsman 917.37561. The adjustable high-back seat, with its ergonomic design, provides support during extended mowing periods, reducing fatigue. Easy-to-use controls are strategically located for accessibility, allowing for smooth operation even for novice users.

Incorporating advanced technologies, this model features mulching capability, which allows users to finely chop grass clippings and return them to the soil, promoting healthier grass growth while reducing the need for bagging. Additionally, the dual blade system offers superior cutting performance, ensuring a clean and even cut every time.

With its combination of power, versatility, and user comfort, the Craftsman 917.37561 stands out as a reliable choice for homeowners looking to maintain their lawns effortlessly. Its blend of advanced features ensures that mowing is not only efficient but also an enjoyable task.
Top Page Image Contents