Craftsman 944.36153 II. Slope Operation, Do not, III. Children, You last saw them, IV. Services

Page 3

Shut the engine (motor) off and wait until the blade comes to complete stop before removing grass catcher.

I_low only in daylight or good artificial light.

Do not operate the machine while under the influence of alcohol or drugs.

Never operate machine in wet grass. Always be sure of your footing: keep a firm hold on the handle and walk; never run.

Disengage the self-propelled mecha- nism or drive clutch on mowers so

equipped before starting the engine (motor).

If the equipment should start to vibrate abnormally, stop the engine (motor) and check immediately for the cause. Vibration is generally a warning of trouble.

Always wear safety goggles or safety glasses with side shields when operating mower.

II. SLOPE OPERATION

Slopes are a major factor related to slip and fall accidents which can result in

severe injury. All slopes require extra caution. If you feel uneasy on a slope, do

not mow it.

DO:

Mow across the face of slopes: never up and down. Exercise extreme caution

when changing direction on slopes.

Remove obstacles such as rocks, tree limbs, etc.

Watch for holes, ruts, or bumps. Tall

grass can hide obstacles.

DO NOT:

Do not trim near drop-offs, ditches or embankments. The operator could lose footing or balance.

Do not trim excessively steep slopes.

Do not mow on wet grass. Reduced footing could cause slipping.

III.CHILDREN

Tragic accidents can occur if the operator

is not alert to the presence of children.

Children are often attracted to the

machine and the mowing activity. Never assume that children will remain where

you last saw them.

Keep children out of the trimming area and under the watchful care of another

responsible adult.

Be alert and turn machine off if children enter the area.

Before and while walking backwards, look behind and down for small children.

Never allow children to operate the machine.

Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision.

IV. SERVICES

Use extra care in handling gasoline and other fuels. They are flammable and vapors are explosive.

-Use only an approved container.

-Never remove gas cap or add fuel with the engine running. Allow engine

to cool before refueling. Do not smoke.

-Never refuel the machine indoors.

-Never store the machine or fuel container inside where there is an

open flame, such as a water heater.

Never run a machine inside a closed area.

Never make adjustments or repairs with the engine (motor) running. Disconnect the spark plug wire, and keep the wire away from the plug to prevent accidental starting.

Keep nuts and bolts, especially blade attachment bolts, tight and keep equipment in good condition.

Never tamper with safety devices. Check their proper operation regularly.

Keep machine free of grass, leaves, or other debris build-up. Clean oil or fuel spillage. Allow machine to cool before storing.

Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting.

Never attempt to make wheel height adjustments while the engine (motor) is running.

Grass catcher components are subject to wear, damage, and deteriorat)on, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturer's recommended parts, when necessary.

Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them.

Do not change the engine governor setting or overspeed the engine.

3

Image 3
Contents Rotary Lawn Mower Limited TWO Year Warranty on Craftsman Power Mower Commercial or Rental USEGeneral Operation III. Children IV. ServicesII. Slope Operation Do notSafety is Involved Howto SET Upyour Lawn Mower To Unfold HandleTo Remove Lawn Mower from Handle Opening To Install AttachmentsTo Assemble Grass Catcher CatcherWithout OIL or Gasoline in the engine Meets Cpsc Safety RequirementsKnowyour Lawn Mower Primer Important This lawn mower is shippedTo Convert Mower To Adjust Cutting HeightHowto Useyour Lawn Mower Engine Speed Engine Zone ControlTo Start Engine To Stop EngineMulching Mowingiips Before Each USE Keep unit well lubricated See LUBRI- Cation ChartWhee adjuster Oneach wheel General RecommendationsDamaged Lawn MowerTires Blade CareMuffler Grass CatcherEngine Lubrication AIR FilterEngine Engine Speed CleaningTo Adjust Handle Rear DeflectorHandle Engine Fuel SystemEngine OIL Correction Troubleshooting Chart Problem CauseCylinder OtherGrass or to hard surface Not venting air Clean GrassReplace MoveRotary Lawn Mower Model Number KEY Part No NO. Description 383 OiiBriggs & STRATiON Engine 97oBriggs & Stratton Engine 455i it745 KEY Part Description Included in Carburetor Gasket Set, Key #977 Get it fixed, at your home or ours

944.36153 specifications

The Craftsman 944.36153 is a remarkable power tool that stands out in the crowded marketplace of handheld oscillating multi-tools. Known for its versatility and efficiency, this model is designed for both professional tradespeople and DIY enthusiasts who require reliable performance for a variety of applications.

One of the standout features of the Craftsman 944.36153 is its powerful motor, which provides ample power to tackle tough materials such as wood, metal, and plastic. The tool is engineered for maximum performance, ensuring that users can complete their projects efficiently without the frustration of inadequate power. Coupled with a variable speed control system, this multi-tool allows users to adjust the speed to suit the specific requirements of their tasks, making it a perfect choice for intricate projects that require precision or heavy-duty applications that demand more power.

Another significant characteristic of the Craftsman 944.36153 is its innovative tool-free blade change mechanism. This feature enables quick and easy swapping of attachments, allowing users to switch between cutting, sanding, and scraping tasks without wasting time. The quick-release lever eliminates the need for additional tools, streamlining the workflow and enhancing productivity.

In terms of design, the Craftsman 944.36153 offers an ergonomic handle that provides comfort during prolonged use. Its lightweight construction reduces user fatigue, making it suitable for extended projects. The tool’s compact design allows for easy maneuverability in tight spaces, an essential feature for decorators, electricians, and carpenters who often work in confined areas.

The Craftsman 944.36153 is also equipped with an oscillating technology that ensures minimal vibrations during operation. This translates to increased precision and control, enabling users to achieve clean cuts and finishes without sacrificing consistency.

Durability is another hallmark of the Craftsman brand, and the 944.36153 lives up to this reputation. Built with quality materials and solid construction, this tool is designed to withstand the rigors of daily use, making it a worthwhile investment for anyone in need of a reliable multi-tool.

In conclusion, the Craftsman 944.36153 is an exceptional oscillating multi-tool that combines power, versatility, and user-friendly features. Whether you're a seasoned professional or a weekend warrior, this tool can help elevate your projects, making it an essential addition to any toolkit. Its thoughtful design and technology make it a top contender in the competitive world of oscillating tools.