Craftsman 917.37892 Blade Care, To Remove Blade, To Replace Blade, To Sharpen Blade, Gear Case

LAWN MOWER

Always observe safety rules when per- forming any maintenance.

TmRES

*Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

*Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

DRmVE WHEELS

Check front drive wheels each time before you mow to be sure they move freely.

The wheels not turning freely means trash, grass cuttings, etc. are in the drive wheel area and must be cleaned to free drive wheels.

If necessary to clean the drive wheels, be sure to clean both front wheels.

1.Remove hubcaps, Iocknuts & washers.

2.Remove wheels from wheel adjusters.

3.Remove any trash or grass cuttings from inside the dust cover, pinion and/ or drive wheel gear teeth.

4.Put wheels back in place.

NOTE: If after cleaning, the drive wheels do not turn freely, contact a Sears or other qualified service center.

BLADE CARE

For best results, blade must be kept sharp. Replace a bent or damaged blade.

TO REMOVE BLADE

1.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

2.Turn lawn mower on its side. Make sure air filter and carburetor are up.

3.Use a wood block between blade and mower housing to prevent blade from

turning when removing blade bolt. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

4.Remove blade bolt by turning counter- clockwise.

5.Remove blade & attaching hardware (bolt, lock washer & hardened washer).

TO REPLACE BLADE

1.Position blade on the blade adapter aligning the two (2) holes in the blade with the raised lugs on the adapter.

2.Be sure the trailing edge of blade (oppo- site sharp edge) is up toward the engine.

3.Install the blade bolt with the lock washer and hardened washer into

blade adapter and crankshaft.

4.Use block of wood between blade and

lawn mower housing and tighten the blade bolt, turning clockwise.

The recommended tightening torque is

mMPORTANT: Blade bolt is heat treated. If bolt needs replacing, replace only with approved bolt shown in the Repair Parts section of this manual.

Blade adapter	Crankshaft
Key	keyway
Lockwasher

Blade

Blade		Crank
		shaft
bolt	Harden_
		\
	washer	Trailing edge Blade adapter

TO SHARPEN BLADE

NOTE: We do not recommend sharpening

the blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade bal- anced.An unbalanced blade will cause even-

tual damage to lawn mower or engine.

The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

To check blade balance, drive a nail into a beam or wall. Leave about one inch of

the straight nail exposed. Place center hole of blade over the head of the nail.

If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

GRASS CATCHER

', The grass catcher may be hosed with water, but must be dry when used.

,,Check your grass catcher often for dam-

age or deterioration. Through normal use it will wear. If catcher needs replac- ing, replace only with approved replace-

ment catcher shown in the Repair Parts section of this manual. Give the lawn

mower model number when ordering.

GEAR CASE

To keep your drive system working properly, the gear case and area around the drive should be kept clean and free of trash build-up. Clean under the drive cover twice a season.

The gear case is filled with lubricant to the proper level at the factory. The only time the lubricant needs attention is if service has been performed on the gear case.

@ If lubricant is required, use only Elf Mul-

35-40 ft. Ibs.

13

tis EP00. Do not substitute.