Craftsman 358.798340 manual UNIfSAFETY

Page 3

i

i

!

i

i,ir

,A IMPORTANT WARNINGS

UNIfSAFETY

oinspect the entire unit before each use for worn, loose, missing, or damaged parts. Do not use until the unit is in proper working order.

Have all internal service performed by qualified ser- vice repair personnel to avoid creating a hazard or voiding your warranty.

-Never run the unit without the proper equipment attached. When used as a blower, always install a blower tube. When used as a vacuum, always install vacuum tubes and collection bag assembly.

Do not use any accessory or attachment other than those recommended by the manufacturer for use with your unit.

*Use only in daylight or in good artificial light.

OPERATION SAFETY

- Keep others including children, animals, bystand- ers, and helpers a minimum of 30 feet (10 meters)

away. Stop the motor immediately if you are ap- proached.

oStop the motor and disconnect the power source before opening the air inlet door or attempting to insert or remove the vacuum tubes. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating bJades.

Inspect the area before using the unit. Remove all debris and hard objects such as rocks, glass, wire; etc. that can ricochet, be thrown, or otherwise cause injury or damage during operation.

When using the vacuum attachment kit, the unit is designed to pick up dry material such as teaves, grass, small twigs, and bits of paper. Do not vacuum stones, gravel, metal, broken glass, etc. to avoid severe dam-

age to the impeller. Do not attempt to vacuum water or other liquids to avoid electrocution.

. Avoid accidental starting. Be sure the switch is in the "off" position and keep your hand and fingers away from the switch while connecting the unit to the power source or when carrying a unitconnected to the power source.

Turn off all controls and allow the motor to stop before disconnecting the unit from the power

source.

Disconnect the unit from the power source when not in use. Do not leave the unitwhen itis plugged into an outlet.

Avoid dangerous environments. Do not use in un- ventilated areas or where dust or explosive vapors can buifd up.

Do not set the unit on any surface except a clean, hard area while the unit is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit, property, or causing seri- ous injury to bystanders or operator.

Do not overreach or use from unstable surfaces

such as ladders, trees, steep slopes, rooftops, etc. Use extra care when cleaning on stairways. Keep firm footing and balance at all times.

Never place objects inside the blower tubes; al- ways direct the blowing debris away from people, ani-

& SAFETY INSTRUCTIONS

iiii

i

iiillm i i

maJs,glass, and solid objects such as trees, automo- biles, wails, etc. The force of air can cause rocks, dirt, or sticks to be thrown or to ricochet which can hurt

people or animals, break glass, or cause other dam- age. Do not allow the unit to be used as a toy.

-Never place any object in the air intake opening as

this could restrict proper air flow and cause damage to the unit.

Never run the unit without the proper equipment attached, When used as a blower, a_ways install a blower tube. When used as a vacuum, atways instatl vacuum tubes and collection bag assembly. Make sure the colJection bag assembly is completely zipped when unit is running to avoid flyin_ debris.

Never use for spreading chemicals, fertilizers, or any other substances which may contain toxic materi- als.

Avoid situations which could set the collection bag on fire. Do not vacuum discarded matches, ci- gars, cigarettes, or ash from fireplaces, barbecue pits, brush piles, etc. To avoid spreading fire, do not use blower near leaf or brush fires, fireplaces, barbecue pits, ashtrays, etc.

Always use the collection bag shoulder strap when vacuuming to avoid toss of control.

Use only for jobs explained in this manual.

MAINTENANCE SAFETY

Maintain the unit according to recommended pro- cedures.

This unit is Double Insulated. See the "DOUBLE

INSULATION" section. Have all service and mainte- nance not explained in your operator's manual performed by a Sears Service Center to avoid creat- ing a hazard and/or voiding your warranty.

Disconnect from power source before servicing, cleaning, performing maintenance, or storing the unmt.

Use only genuine replacement parts as recom-

mended by the manufacturer to avoid creating a haz- ard and/or voiding your warranty.

°Never douse the unit with water or other liquids or squirt with a water hose. Clean with a damp sponge and mild soap. See "STORAGE".

°Check air intake openings, blower tubes, elbow tube, and vacuum tubes frequently, always with the

unit stopped and the power source disconnected. Keep vents and tubes free of debris which can accu- mulate and restdct proper air flow.

Do not attempt to repair unit. Repairs must be per- formed by a Sears Service Center. Have all mainte- nance other than the recommended procedures de-

scribed in the Operator's Manual performed by a Sears Service Center.

Always have your Sears Service Center replace a damaged Impeller. Parts that are chipped, cracked, broken, or damaged in any other way can fly apart and cause serious injury. Have damaged parts repiaced before using the unit.

Do not burn, incinerate, or expose this unit to extreme heat.

Store the unit unplugged in a hi_.h, cool, dry, in- doors area out of the reach of children.

ffsituations occur which are not covered in this manual, use care and good judgmenL

ff you need assistance, contact your SEARS Service Center/Department or carl the

CUSTOMER ASSISTANCE HOTLINE at 1.800-235-5878.

SAVE THESE INSTRUCTIONS

Image 3
Contents Important Manual SE/ RSIMPORTANTlilt iiii iWARNINGSii ii& SAFETYi i iINSTRUCTIONSi UNIfSAFETY Full ONE Year Warranty on Craftsman Electric Blower Customer ResponsibilitiesDate of Purchase Table of Contents AccessoriesIndex Hardware Contents Assembly Vacuum Tube Assembly , 7Removing the Inlet Restrictor Fig Blower Conversion Adjusting the Shoulder Strap onMinimum Wire Gauge Recommendation Chart Collection BAGCheck List Know Your Electric Blower Double Insulation ConstructionOperating Positions SafetyANY Maintenance on the Collection BAG OperationOperating Your Unit Using Your Unit AS a Blower FigUsing Your Unit AS a Vacuum Fig Stopping Your UnitAfter Each USE Customer ResponsibilitiesGeneral Recommendations Before Each USEStorage Service and AdjustmentsTroubleshooting Points Troubleshooting ChartPage If YOU Need Repair Service or Parts Ordering Parts 1-800-WON-PART AssistancePart Number Part Description

358.798340, 79834 specifications

The Craftsman 358.798340 and 358.79834 are notable models from Craftsman, a brand well-regarded for its durable and effective outdoor power equipment. These models are primarily designed for users who require an efficient and reliable tool for lawn care and maintenance tasks.

One of the standout features of the Craftsman 358.798340 and 358.79834 is their robust engine performance. Both models are equipped with a 25cc 2-cycle engine that provides ample power for trimming grass, weeds, and overgrowth in residential and commercial spaces. This engine technology ensures that users can tackle challenging tasks without the concern of stalling or losing momentum.

Both models are designed with user comfort in mind. They feature cushioned handlebars that reduce vibration during operation, making it easier for users to handle the trimmers for extended periods without experiencing fatigue. Additionally, the lightweight design ensures easy maneuverability, allowing users to navigate tight spaces and uneven terrain effortlessly.

Another important attribute is the ease of starting. These trimmers feature an Easy Start technology which minimizes the effort needed to start the engine, a significant advantage for individuals who may struggle with traditional pull-start mechanisms. The efficient starting system contributes to a hassle-free experience, enabling users to focus on their trimming tasks rather than dealing with difficult ignition systems.

The Craftsman 358.798340 and 358.79834 also incorporate advanced cutting technology. The 18-inch cutting path and dual-line cutting system allow for a more extensive area to be covered in a single pass, thereby increasing efficiency. The automatic feed spool provides a continuous line feed, simplifying the process of line replacement and reducing downtime.

Additionally, these models are compatible with a variety of accessories and attachments, enhancing their versatility. Users can easily switch between trimming and edging tasks, making them a highly adaptable choice for different landscaping needs.

Overall, the Craftsman 358.798340 and 358.79834 stand out due to their powerful engine, user-friendly features, and efficient cutting capabilities. They are designed to meet the demands of homeowners and professionals alike, providing a reliable solution for effective lawn care maintenance. With these trimmers, users can expect to achieve a well-manicured lawn with ease and confidence.