Craftsman 358.352680 - 18 IN. BAR Trouble Shooting Chart, Not move tight, Guide bar rails pinched

Page 18

TROUBLE SHOOTING CHART - Continued

TROUBLE CAUSE

Chain moves • Idle speed requires

at idle speed. adjustment.

•Clutch requiresrepair.

Chain does • Chain tension too

not move tight.

when engine E*Carburetor requires is accelerated. adjustment.

•Guide bar rails pinched.

•Clutch slipping.

Chain clatters • Chain tension incorrect.

or cuts roughly,• Cutters damaged.

•Chain worn.

•Cutters dull, improperly sharpened, or depth gauges too high.

I.Sprocket worn.

•Chain installed backwards.

i .....

REMEDY

• See "Carburetor Adjustments."

*Contact SearsService. o See "Chain Tension,"

•See =CarburetorAdjustments."

•Repairor replace.

•ContactSears Service.

•See =ChainTension."

•ContactSearsService.

•Resharpenor replace chain.

•See =SharpeningChain."

•Contact Sears Service.

•Install chain in right direction.

Chain stops within the cut.

Chain cuts at

an angle.

•Chain cutter tops not filed flat.

•Guide bar burred or bent; rails uneven.

,Clutch slipping

•Cutters damaged on one side.

•Chain dull on one side.

•Guide bar bent or worn.

•See "Sharpening Chain."

•Repair or replace guide bar.

•Contact Sears Servk'e.

•See "Sharpening Chain."

•See "Sharpening Chain,"

•Replace guide bar.

If situations occur which are not covered in this manual, use care and good judgement. If you need assistance, contact Sears Service or the CUSTOMER ASSISTANCE HELPUNE at 1-800-235-5878.

18

Image 18

Contents CRRFTSNRNo Parts List Plan AheadMaintain Your SAW in Good Working Order Operate Your SAW SafelyGuard Against Kickback Handle Fuel with CautionKickback Safety Features Maintain ControlCarton Contents AssemblyPrimer Bulb Carburetorto providequicker startingIf you do not understandthe fuel han Before Starting EngineSectionofthis manual beforeyou begin Customerassistancehelp lineatStarting a Warm Engine Release throttle trigger to allow engine to idleOperating Tips Keep the engine at full speedAfter removingthe wood, make Notch.This is done by making a cutLimbing Pruning Bucking Using a LOG or Support StandAlwaysmake yourfirst cut on the compressionside of the log Important PointsCustomer Responsibilities General RecommendationsLubrication Check Chain Tension Check for Damaged or Worn PartsCheck for Loose Fasteners and Parts Check Guide BARCleaning the Spark Arrestor Screen Clean Unit & LabelsClean AIR Filter Inspect Muffler and Spark Arrestor ScreenChain Adjustment See Chain Tensionin Maintenance sectionChain Replacement Carburetor Presets Clean Fuel FilterCarburetor Adjustment Adjusting ProcedureEngine Fuel SystemOther Hot Trouble Shooting ChartEnginewUl not idle properly RemedyGuide bar rails pinched Trouble Shooting ChartNot move tight An angleRepair Parts LUlnlIIIIIIIHII IIIn Repair Parts Piense Antes DE Proceder Siempreel calde de la bujfa al repararHeridas As/ada GuantesdeFuncionamiento Maneje EL Combustible CONProtejase Contra LAS Reculadas Mantenga EL Control Redlizca LAS Probabilidades DE ReculadaNo de meted,para mantenerabiertoel code Tocones, etc. El!mine o evite todaDispositivos DE Seguridad Contra I.AS Reculadas Entumecimiento,el dolor,la falta deContenido DE LA Caja MontajeConozca EL Aparato Manualpard usofuturoEodes y= Abastecimiento DEL Motor Aceite Para Barra Y LA CadenaPara Parar EL Motor Para Poner EL Motor ENAcelerada Sugerencias Para EL USOCorrecto DEL Aparato Tecnicas Para Tumbar Arboles Planue unarata X,Ppredetermhladaydespejada De retmcesoLaCafda Para Tumbar Arboles GrandesCorte DE UN Arbol Tumbado Advertencia No se pare encimaPuntos importantes Forma Seccionamiento UsandoAdvertencia Para Cortar Ramas Y PodarUsar Gasdas Vedfiqueque nohayafijdores/pie- e Zassueltas Para PodarResponsabilidades DEL Usuario Cambie ia bujiaVerifique QUE no Haya Piezas DAtADAS O Gastadas Verirque QUE no Haya Rjadores O Piezas SueltasVerirque LA Tension DE LA Afilaci6n Verifique SI LA Cadena Esta AfiladaArlacion DE LA Cadena Limpie EL Aparato Y LAS PlacasMuy filosa y puede cortaraun no Estandoen movimientoEs normal que las cadenas nuevasse Quedar sin combustible,luego retire el Ajuste DE LA CadenaMmpie EL Filtro DE Combustible Ajustes AL CarburadorPuntos DE Precalibracion No Haga Funcionar EL MotorOtro Superficies ExternasMotor Empiezaa oxidarTabla DIAGNOS1TCA Problema MotorestahogadoSolucion Cdrnbielaparla bujlacotrectaVea AjustesalCazbwador AceiteparePage Page Part Americas Repair Specialists