Weed Eater WET2242STC manual To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig

Page 19

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 14

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 17

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 18)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. WET2242STC Safety Rules Safety Rules Table of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigTo Remove Wheel for Repairs See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERInterlocks and Relays To Replace Headlight BulbTo Replace Fuse To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WET2242STC SchematicElectrical KEY Part Description Chassis and Enclosures 219 17670508 Screw 5479J Plug Btn Blk Drive Shaft Asm Cross Tapered PMST/20 Steering Assembly Nut Hex Jam Toplock 1/2-20 Unf Engine Gasket Order Parts From Engine Manufacturer Seat Assembly Wheels & Tires DecalsMower Lift 159460 Mower Deck Mandrel Assembly Includes Hous Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation

WET2242STC specifications

The Weed Eater WET2242STC is a versatile and robust string trimmer designed for efficient lawn care and garden maintenance. Equipped with a powerful 22cc 2-stroke engine, this trimmer offers impressive performance that allows users to tackle tough vegetation and overgrown areas with ease. Its lightweight design, weighing just around 10 pounds, ensures comfortable handling and reduced fatigue during extended use.

One of the standout features of the WET2242STC is its innovative StartEasy technology, which simplifies starting the engine. Users can enjoy a hassle-free start with less effort, making it accessible even for those who are less experienced with power tools. This feature enhances the overall user experience by minimizing frustration and downtime that can occur with traditional pull-start engines.

The WET2242STC is equipped with a dual line automatic feed head, allowing for quick and easy line replacement without the need for tools. This system feeds out the cutting line as needed, ensuring optimal cutting performance and eliminating the hassle of manual line adjustments. The trimmer’s 17-inch cutting diameter provides an extensive area coverage, making it an ideal choice for efficiently trimming larger lawns and garden spaces.

Designed for user comfort, the trimmer features an adjustable handle that can be customized for different users and operating positions. The straight shaft design also allows for access to tight spaces and hard-to-reach areas, such as under bushes or around garden beds, delivering precision cutting where it’s needed most.

Furthermore, the WET2242STC boasts a durable construction with a solid combination of plastic and metal components, ensuring longevity and reliability for repeated use over the seasons. The lightweight frame, combined with the ergonomic design, enhances maneuverability, allowing users to navigate around obstacles seamlessly.

In summary, the Weed Eater WET2242STC stands out with its powerful engine, user-friendly features, and comfortable design. With advanced technologies like StartEasy and an automatic line feeding system, this trimmer is a fantastic solution for homeowners and gardening enthusiasts looking to maintain their outdoor spaces efficiently and effectively. Whether tackling tough weeds or outlining garden beds, the WET2242STC proves itself as a reliable partner in lawn care.
Top Page Image Contents