Weed Eater 952711474 Collection BAG Assembly, Adjusting the Shoulder Strap on the Collection BAG

Page 6

4.To attach the lower vacuum tube to the upper vacuum tube, first align the arrows on the two tubes. Then, press the two tubes together until the lower tube is securely seated in the upper tube (about 3 inches).

Upper Tube Lower Tube

Align arrows on upper and lower tubes

COLLECTION BAG ASSEMBLY

1.Open the zipper on the collection bag and insert the elbow tube.

2.Push the small end of the elbow tube through the small opening in the bag.

NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube and the hole for the tube release button is on top.

Elbow Tube

Tube

 

Release

 

Button

 

Hole

Zipper

Small

Opening

Opening

 

3.Close the zipper on the bag. Make sure the zipper is closed completely.

4.Align the grooves on the elbow tube with the grooves on the blower outlet.

5.Push the elbow tube onto the blower outlet until it snaps into place (elbow tube is secured by red tube release button).

ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG

1.Carefully loop the shoulder strap through the buckle as shown in the il- lustration below.

Last In

First In

2.Position the unit on your right-hand side, blower outlet and bag pointing toward the rear. Hold the unit in an upright position with the lower vacu- um tube on the ground to support it.

3.Place the shoulder strap over your head and onto your left shoulder.

4.Adjust the strap to allow a free flow of air from the blower. If the collection bag is kinked, the unit will not operate properly.

NOTE: The strap is designed to posi- tion the collection bag on your shoulder without kinks. The strap is not intended to support the weight of the unit.

Shoulder strap on left shoulder

No kinks in bag allows free air flow

HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE

1.Stop unit and unplug the extension cord.

2.Remove the vacuum tubes by insert- ing the tip of a screwdriver into the latch area on the vacuum assist han- dle. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacu- um assist handle with your other hand.

Latch Area

Vacuum

Assist

Handle

3.Install the inlet restrictor that was re- moved when assembling for vacuum use.

NOTE: If you are unable to locate the inlet restrictor, the unit will still operate. This restrictor improves the blower function.

4.Remove the collection bag.

5.Close the inlet cover and make sure it is latched closed.

6.Re-install the blower tube. Refer to AT- TACHING THE BLOWER TUBE for instructions on how to attach this item.

SELECT AN EXTENSION CORD

Use only a 120 A.C. voltage supply as shown on nameplate of the unit to power your blower.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents English Español Français AdvertenciaAvertissement Safety Rules Operator SafetyElectrical Safety Double Insulation Construction UNIT/MAINTENANCE SafetyStop the motor immediately if you are ap- proached Servicing of Double Insulated BLOWER/VACUUMUse only in daylight or in good artificial light Blower SafetyVacuum Safety StandardsVacuum Assembly AssemblyBlower Assembly Standard screwdriver is required for as- semblyHOW to Convert Unit from Vacuum USE to Blower USE Collection BAG AssemblyAdjusting the Shoulder Strap on the Collection BAG Stop unit and unplug the extension cordON/OFF Switch Inlet Cover Latch ON/OFF Switch is used to activateKnow Your Electric BLOWER/VACUUM Maintenance Before Each USEService StorageAfter Each USE Troubleshooting Table Symptom Cause Remedy Weed Eater

952711474 specifications

The Weed Eater 952711474 is a remarkable tool that has revolutionized lawn maintenance for both homeowners and professional landscapers. Known for its efficiency and innovative features, this string trimmer stands out in the market, making it an essential gardening companion.

One of the main features of the Weed Eater 952711474 is its lightweight design. Weighing just around 10 pounds, this trimmer is easy to maneuver, allowing users to trim grass and weeds effortlessly over large areas without causing fatigue. Its adjustable handle ensures comfort during operation, accommodating users of various heights and preferences.

Equipped with a powerful 25cc gas engine, the Weed Eater 952711474 delivers high performance, ensuring effective cutting through thick grass and overgrown weeds. The engine provides ample power while maintaining fuel efficiency, allowing for extended work time without frequent refueling. This is particularly beneficial for larger lawns or more extensive landscaping projects.

The trimmer also features a dual-line feed system, which allows for a wider cutting path and quicker completion of trimming tasks. The easy-to-load spool makes string replacement a breeze, minimizing downtime and enabling users to get back to work quickly. The automatic line advancement technology further enhances efficiency, ensuring that the cutting line only advances when needed, reducing waste and saving money.

Another significant characteristic of the Weed Eater 952711474 is its versatility. It comes with a variety of compatible attachments, allowing users to convert the trimmer into different gardening tools such as edgers or pruners. This adaptability makes it a valuable investment for maintaining a well-groomed landscape.

The ergonomic design of the Weed Eater 952711474 promotes ease of use, with a comfortable grip and an easily adjustable shaft for reaching tight spaces. Additionally, it has anti-vibration technology that reduces fatigue during prolonged use, enhancing overall user experience.

In summary, the Weed Eater 952711474 is a standout choice for anyone seeking an efficient and user-friendly string trimmer. With a combination of lightweight construction, powerful engine, dual-line feed system, and versatile attachment options, it delivers exceptional performance for all your trimming needs, making lawn care a more enjoyable task.
Top Page Image Contents