Weed Eater 174193, WE12542F To Adjust Throttle Control Cable See Fig, To Adjust Carburetor

Page 23

SERVICE AND ADJUSTMENTS

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 28)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

•Check that holes “A” in governor control lever and hole in governor plate line-up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned. Tighten clamp screw securely.

	GOVERNOR	GOVERNOR
	CONTROL LEVER	GOVERNOR
	CONTROL LEVER	CONTROL
		CONTROL
		PLATE
HOLES “A”	CLAMP	THROTTLE
	SCREW	CABLE
		CABLE

FIG. 28

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE

GOVERNOR, WHICH IS FACTORY SET FOR PROPER

ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE

THE FACTORY HIGH SPEED SETTING CAN BE

DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED

HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR

N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R /

DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND

E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y

ADJUSTMENTS.

23

Image 23

Contents Model NO. WE12542F Safe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Customer Responsibilities Product SpecificationsSlope Sheet Unassembled PartsSteering Wheel Seat KeysBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor To USE Throttle Control see FIG HOW to USE Your TractorTo Adjust Mower Cutting Height See Fig Stopping See Fig To SET Parking Brake See FigTowing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To TransportTo Start Engine See Fig Mowing TipsBefore Each USE ¿ Lubrication ChartCustomer Responsibilities General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR Screen See FigTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel AlignmentInterlocks and Relays Replacing Battery SeeTo Remove Hood and Grill Assembly See Fig To Replace Headlight BulbTo Adjust Carburetor To Adjust Throttle Control Cable See FigEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WE12542F SchematicElectrical KEY Part NO. NO.DESCRIPTION Chassis KEY Part Description Drive Transaxle Steering KEY Engine 140310 Control Th/ch Flag Seat Wheels & Tires DecalsMower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Sevice Sighting Guide Suggested Guide for Sighting Slopes for Safe Operation