To Stop the Engine, Starting Position

gutters, screens, patios, grills, porches, and gardens.

D Watch out for children, pets, open win- dows, or freshly washed cars. Blow debris away safely.

DUse the full blower nozzle extension so the air stream can work close to the ground.

DAfter using blowers and other equipment, CLEAN UP! Dispose of debris in trash re- ceptacles.

This engine is certified to operate on un- leaded gasoline. Gasoline must be mixed with a good quality 2-cycle air-cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/Weed Eater brand oil is recom- mended. (A 40:1 ratio is obtained by mixing

3.2ounces of oil with 1 gallon of unleaded gasoline). When mixing fuel follow the instructions printed on the container. Always read and follow safety rules under HANDLE FUEL WITH CAUTION in the SAFETY RULES section.

TO STOP THE ENGINE:

DTo stop engine, move switch to STOP.

BEFORE STARTING THE ENGINE:

D Fuel the engine. Move at least 10 feet (3 meters) away from the fueling site.

D Hold the unit in the starting position as shown. Make sure the blower end is di- rected away from people, animals, glass, and solid objects.

STARTING POSITION

BLOWERVACUUM

WARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing se- rious injury to bystanders or the operator.

Throttle Switch

Trigger

Throttle

Lock

Choke Lever

(shown in HALF CHOKE position)

STARTING A COLD ENGINE (or a warm engine after running out of fuel):

DMove switch to the ON position.

DActivate the throttle lock as follows: D squeeze and hold throttle trigger; D press and hold throttle lock, then D release the throttle trigger

DMove choke to FULL CHOKE position.

D Pull starter rope handle sharply until en- gine attempts to run, but NO MORE THAN 6

PULLS.

LISTEN: The engine may sound as if it is trying to start before the 6th pull. This sound may be hard to hear. If so, go to the next step immediately.

DMove choke to HALF CHOKE position.

D Pull starter rope handle sharply until en- gine runs, but no more than 6 pulls.

NOTE: If engine has not started after 6 pulls, repeat all of the above steps.

DAllow engine to run for 10 to 15 seconds,

then move choke to OFF CHOKE position.

DSqueeze and release the throttle trigger to release the throttle lock.

NOTE: If engine dies with choke at OFF CHOKE position, move the choke to the HALF CHOKE position and pull the starter rope han- dle 5 more times. If engine does not start and operate properly, refer to CARBURETOR AD-

JUSTMENTS.

DTo stop engine, move switch to STOP.

STARTING A WARM ENGINE:

D Move switch to the ON position.

D Move choke to HALF CHOKE position. D Activate the throttle lock.

D Pull starter rope handle sharply until en- gine runs, but no more than 6 pulls.

D Move choke to OFF CHOKE position. Then, squeeze and release the throttle trigger to release the throttle lock.

NOTE: If engine does not run after 5 pulls, it is probably flooded. Wait a few minutes and repeat procedure with choke at OFF CHOKE.

D To stop engine, move switch to STOP.

-- 5 --

530087724 specifications

The Weed Eater 530087724 is a versatile and reliable tool designed for homeowners and professionals seeking an efficient solution for lawn care. This string trimmer is known for its ease of use, outstanding cutting performance, and durable construction, making it a preferred choice among garden enthusiasts.

One of the main features of the Weed Eater 530087724 is its powerful two-cycle gas engine. This engine offers a robust performance, enabling users to tackle thick grass, weeds, and tough vegetation with minimal effort. The engine's design maximizes fuel efficiency, allowing users to work longer without frequent refueling.

The trimmer also boasts a lightweight design, which enhances maneuverability and reduces operator fatigue during extended use. Weighing in at just a few pounds, it is comfortable to handle, enabling users to navigate around flower beds, trees, and uneven terrain easily. Its looping handle further adds to its ergonomic design, allowing for precise control and reducing strain on the user's wrists.

Another notable characteristic is the adjustable cutting width. The Weed Eater 530087724 offers a cutting width that can be easily modified to suit various tasks, from trimming delicate grass around ornamental plants to clearing out tougher weeds in larger areas. This versatility ensures that it is suitable for a range of applications, whether maintaining a small garden or managing a more extensive landscaping project.

Furthermore, the Weed Eater 530087724 incorporates advanced technology in its design. The automatic feed spool simplifies the process of replacing the cutting line, making it easier for users to maintain optimal cutting performance. This eliminates the hassle and downtime associated with manual line adjustments, allowing for a more seamless lawn care experience.

Durability is another highlight of the Weed Eater 530087724. Constructed with high-quality materials, it is built to withstand the rigors of outdoor use. Users can count on its long-lasting performance, even when used in challenging conditions.

Overall, the Weed Eater 530087724 combines power, efficiency, and user-friendly features, making it an excellent choice for anyone looking to maintain a well-groomed lawn and garden. Its adaptability and reliability ensure that it remains a staple tool for all your trimming needs. Whether you're a novice gardener or an experienced landscaper, this trimmer delivers the performance and convenience required to keep your outdoor spaces looking their best.